控制继电器

变速控制继电器输出（切换B（））

Transmission control relay output ( switched b )

EASY可编程控制继电器及其在建筑电气中的开发与应用

EASY Programmable Control Relay and Its Development and Applications in the Field of Architecture Electricity

用easy控制继电器实现锅炉排渣系统故障检测报警

Fault Warning of Boiler Slag-off System by Using " easy " Control Relay

维修短路到OD压力开关感知电路的变速控制继电器输出电路。＊

Repair the trans control relay output circuit shorted to OD pressure switch sense circuit .

电磁控制继电器接触可靠性的提高和实现

Improvement and Realization of Reliability in Contact of Electromagnetic Control Relays

此外，还有许多保护继电器和控制继电器。

In addition , there are many protective and control relays .

矿井提升机控制继电器性能检测研究

Study on the performance check of control relay of a mine hoist

一种新型的继电器&可编程控制继电器在长丝后纺加弹机上的应用

Application of a New Relay & Programmable Control Relay in Filature Production

浅析执行电源板和控制继电器板的典型故障

Simple Analysis on Typical Trouble of Execution Power Panel and Control Relay Panel

关于无触点化技术在执行电源板控制继电器板中应用的研究

Research on Application in Execution Power Panel and Control Relay panel for Non-Contact Technique

三资独占鳌头产品出口为主&控制继电器行业特点及发展趋势

Features and trends of our relay industry

通过内部安装控制继电器，特殊控制开关进行操作就如同电磁阀一样。

Special control switch setup operates like a solenoid valve through internally mounted control relay .

替换变速控制继电器。＊

Replace the transmission control relay .

应急制动控制继电器

Emergency braking control relay

变速控制继电器输出

Trans Control Relay Output

电路板往往被置于从电气上控制继电器开路和闭合的设备上。

The boards are often placed in a mainframe that electronically controls the opening and closing of the relays .

我们已知的假冒产品包括控制继电器，断路器，插座，漏电断路器和其他电器产品。

Such items known to be counterfeited include control relays , circuit breakers , receptacles , ground fault circuit interrupters and other electrical products .

三档点火锁中的启动挡的输出端连接行车准备控制继电器。

The output end of the starting gear in the three-gear switch of the ignition lock is connected with a running preparation control relay .

当加热温度超过预先设定的最高温度值时，通过温控仪控制继电器的闭合打开水路控制电磁阀进行冷却降温处理。

When heat tempera-ture exceeds the highest temperature pre-set , temperature control instrument con-trol relay close to open water control electromagnetic valve for cooling treatment .

经查是与四通阀线圈串联的控制继电器触点接触不良，电阻增大，致使电压降低。

The check is in the series of coil and four-way reversing valve control relay contact resistance increases , the bad , the contacts the voltage reduced .

本文简要介绍电气设备安全防火中传统闸刀开关、自动开关、控制继电器的选型，安装与维护应注意事项。

The points for attention about the selection , installation and safeguard of the traditional switch , auto-switch and relay of electrical equipments for safety fireproof were introduced .

本文对执行电源板、控制继电器板进行了深入的分析，提出了用无触点电子元件替代电磁继电器的设想，从而达到降低故障率的目的。

This paper makes a thorough analysis to execution power panel and control rely panel and puts forward the image of replacing electromagnetism relay with non-contact components so that reach the target of reducing the rate of trouble .

本文列举了执行电源板和控制继电器板的典型故障并对其产生的原因做了简要分析，目的是便于维修人员对症下药，直观的去维修。

This paper give an example of typical trouble of execution power panel and control relay panel and make a simple analysis for its reason rised , the aim is quite easy to suit servance men ' methods to the situation to maintain directly the units .

在1号高炉中修时对上料系统进行了改造，用PLC控制取代继电器控制。

During the intermediate repair the charging system of No1 blast furnace was modernized and PLC control system replaced relay control .

根据用户需求，系统采用单片机和CPLD相结合的方式来控制高压继电器组，为实现快速自动测试和自动搜索故障提供了硬件基础。

According to the request of consumer , the system adopt the SCM and CPLD to control the high voltage relay unit , and offer the basis of hardware for the high-speed automatic test and automatic search the hitch .

单片机控制的继电器参数测试仪

Detecting Device of Relay Parameter Controlled by a Single-Chip Microcomputer

控制系统继电器可靠性分析与措施

Reliability analysis and countermeasures of relays in the control system

单片机控制热继电器自动等离子弧焊接系统

Automatic Plasma Arc Welding System for Thermal Relay on Base of Single-Chip Computer

电动机控制用继电器电机放大器控制系统

Motor control relay amplidyne control system

根据雷达发射机模块化设计的特点，通过使用某软件，以某项目发射机控制机柜继电器盒插件的设计为例，介绍三维参数化实体造型软件在雷达发射机模块化设计中的应用。

The application of parameterization moulding software in transmitter modularization design is introduced by taking an example of using a software to design the relay box plug-in unit in the transmitter cabin of a radar .