点火模块

电子点火模块与分电器的匹配

A Method for Matching an Electronic Ignition Module to Its Distributor

只有杆式点火模块被诊断为有故障时才进行更换。

Only replace bar ignition module if it was diagnosed as faulty .

从线束上分离6个杆式点火模块。

Separate the six bar ignition modules from the wire harness .

汽车发动机电子点火模块性能测试方法的研究

Research on Properties Test Methods of Electronic Ignition Blocks for Automobile Engines

将所有对齐的杆式点火模块安装到对应的气门室盖中。

Fit all bar ignition modules aligned into the corresponding valve cover .

数字式点火模块自适应控制的研究

A Study on Adaptive Control for Digital Ignition Module

拆下杆式点火模块的保险丝。

Remove the fuse for the ignition rod modules .

安装杆式点火模块和喷射系统的保险丝。

Fit the fuses for the ignition rod modules and the injection system .

松开接头并依次从条形点火模块中拔出。

Release connector and pull off in sequence from the bar ignition modules .

将螺钉安装到杆式点火模块上。

Fit screws on the bar ignition modules .

汽车点火模块的厚膜封装技术

Thick Film Assembling Technology of car Ignition Module

汽车多用电子点火模块的设计

Design of Automobile Multi purpose Electronic Ignition Module

有损坏杆式点火模块的危险！

Risk of damage to bar ignition modules !

用于拆卸杆式点火模块。

For removing the ignition rod modules .

读取该车辆发动机上所有杆式点火模块的零件号。

Read off the part number on all bar ignition modules on the engine of this vehicle .

按照运动方向扭转曲轴，直至杆式点火模块再次露出并可听到啪哒声。

Twist the crankshaft in the direction of motion until the ignition rod module comes out again with an audible plop .

硬件设计部分包括采集卡及传感器选择、传感器输入信号处理电路、点火模块驱动电路、电源电路设计等。

Hardware design includes : choice of DAQ and sensors , designs of sensors input signal circuit , ignition actuating circuit and power supply circuit .

在叙述点火模块厚膜电路的生产过程中系统介绍了厚膜封装工艺、相关设备、技术参数和检测方法。

This pa-per introduces thick film assembling technique , equipment , technical parameters and testing methods while narrating the manufacturing process of thick film circuits .

这些模块必须作为整体部件单元或者作为单个零件进行更换，具体取决于所安装的杆式点火模块的零件号；参见？“所需操作：”。

The modules must be replaced either as a complete unit or individually , depending on the part number of the installed bar ignition modules ; see ?" Action required : " .

对其整体式、定线圈式、点火模块控制电路厚膜化等结构特点进行了详细论述。对点火模块控制电路的工作原理进行了分析。

It narrates in detail the structural features of its integrate style , constant coil style , ingnition module controlling circuit thick film and analyzes the working principles of ignition module controlling circuit .

松开连接右杆点火开关模块的管路。

Unclip line to the right bar ignition modules .

这对于不能用万用表进行测试的部件（比如点火杆模块）或可能因为透入湿气而导致偶然故障的部件而言尤其重要。

This is particularly important for components that cannot be tested with a multimeter , e.g.the ignition bar modules , or components that can cause sporadic faults due to penetrating moisture .

汽油发动机点火能量控制模块研究

The Studying of Ignition Energy 's Control Model of Gasoline Engine

基于神经网络的发动机点火能量控制模块研究

Research of Gasoline Engine Ignition Energy ′ s Control Model Based on Neural Network

点火器控制模块设计

Module Design of Igniting Device

软件设计部分包括转速计算模块、点火时间计算模块、点火控制模块和曲线拟合等的程序编写。

Software design includes : writing programs of rotate speed computing module , ignition timing computing module and ignition control module and curve fitting .

另外，介绍了该系统主要部件的检查，即点火线圈、点火模块及曲轴位置传感器的检查。

In addition , inspection on the main components of the system , including ignition coils , ignition modules and crankshaft positioning sensors , are introduced .

另外，介绍了点火线圈、曲轴位置传感器、凸轮轴位置传感器、点火控制模块、爆震传感器等部件的功能，以及该系统的检修。

Besides , the functions of components , like ignition coil , crankshaft position sensor , camshaft position sensor , ignition control module , knock sensor and the inspection and maintenance procedures are also introduced .