点入

  • 网络Pointing in;dot into
点入点入
  1. 抑制主变压器中性点入地直流电流的几种措施

    Several Measures for Suppressing Direct Current in Neutral Point of Main Transformer

  2. 最后给出工厂仪表系统接地单点入地的方式。

    A module for single point grounding of factory instrument system is described .

  3. 多点入流汇流计算法在北京城市洪水计算中的应用与研究

    Study on Application of Multi-point Inflow and Confluence Calculation Method to Flood in Beijing

  4. 故障电流多点入地接地网接地阻抗数值分析

    Numerical Analysis of Grounding Impedance for Grounding Grids with Multi-Points Short Circuit Current into the Ground

  5. 刚开始的新手朋友可以先试着晚一点入弯尝试寻找下这个感觉。

    Beginning novice friends can first try to come later into the corners trying to find this feeling the next .

  6. 本文对通常的区域填充扫描线算法进行改进,用区段端点入栈替代种子点入栈。

    Instead pushing seed points into a stack , this paper presents a new scanline algorithm for filling area by pushing span ends .

  7. 其中一个方法是监测消费者在网站点入付账页面的速度:那些看起来已经决定了的买家不需要通过特价来吸引。

    One way to do this is to monitor how quickly shoppers click through towards the online seller 's payment page : those who already seem set on buying need not be tempted with a special offer .

  8. 削减大阁镇、赤城县城生活点源入河量对降低潮、白河TN入库负荷影响较小,但对降低TP入库负荷影响较大。

    Cutting domestic point sources in the towns of Dage and Chicheng will reduce total phosphorous loadings , but will have less effect on total nitrogen loadings .

  9. 该临床试验I期主要针对Neuralstem公司的干细胞、手术过程以及直接将药物多点注射入脊髓灰质要求的设备进行安全性评估。

    The trial will study the safety of Neuralstem 's cells and the surgical procedures and devices required for multiple injections of the drug directly into the grey matter of the spinal cord .

  10. 单膜孔肥液点源入渗水分特性研究

    Analysis of the Water Characteristic in Film Hole Fertilizer Solution Infiltration

  11. 滴灌点源入渗湿润锋影响因子的研究

    Influence Factors on Soil Wetting Front under Point Drip Irrigation

  12. 充分供水条件下多因子点源入渗模型研究

    Study on Point Source Infiltration Model under Adequate Water Supply

  13. 点源入渗土壤水分运动规律实验研究

    Experimental study on soil water movement from a point source

  14. 间歇供水条件下点源入渗规律研究

    The effect of intermittent water administration by point source on infiltration patterns

  15. 点源入渗理论及其模型研究进展

    The Advance in Theory and Models of Point Source Infiltration

  16. 保罗:我从度假回来后,就觉得有点不入状况。

    Paul : I feel out of the loop after my vacation .

  17. 正确的选择进钉点和入钉方向可以降低神经根和椎动脉损伤的发生率。

    Implanting screw by correct means can reduce the rate of neurologic complications .

  18. 点源入渗研究进展

    Review of Study on Infiltration from Point Sources

  19. 膜孔灌充分供水点源入渗研究进展

    Research advances of point source infiltration under film hole irrigation with sufficient water supply

  20. 膜孔灌溉点源入渗模型的建立与验证

    Establishment and Verification of the Point Source Infiltration Model for the Filmed Hole Irrigation

  21. 点源入渗等效半球模型的推导和实验验证

    The Algebra Testify and Experiment Validation of Effective HemisPhere Model for Point Source Infiltration

  22. 土壤质地、密度及供水方式对点源入渗特性的影响

    The influence of soil texture bulk density and water applied methods on point source infiltration

  23. 田间点源入渗试验的水盐分布特征分析

    An Analysis of Water and Salt Distribution of the Point Source Infiltration Tests in the Fields

  24. 土壤质地、滴头流量、土壤密度以及供水方式等因素对于点源入渗有着一定的影响。

    Soil texture , bulk density and water applied methods are critical factors influenced point source infiltration .

  25. 间歇供水对点源入渗土壤湿润体及水分分布的影响

    The Influence of Intermittent Water Application by Point Source on Wetted Soil Volume and Soil Water Distribution

  26. 本文介绍了国内外点源入渗的研究成果。

    This paper introduces the research results on the infiltration from point sources at home and abroad .

  27. 不同施肥方式的单膜孔点源入渗水肥运移特性研究

    Study on the laws of the water and fertilizer in the different fertilization of single-film hole irrigation

  28. 由膜孔灌水流推进和消退资料推求点源入渗参数

    Determination of Point Source Infiltration Parameters with Water Flow Advance and Regression Data in Film hole Irrigation

  29. 点源入渗可分为非充分供水点源入渗和充分供水点源入渗两大类。

    Infiltration from point sources can be classified as two categories based on ponding and un ponding water .

  30. 使用不同的机械雾化喷嘴,在不同温度点喷入不同流量的氨水。

    Aqua ammonia with different flow rate was injected into the furnace at different temperature locations by different mechanical atomizers .