冷室
- 名Cold chamber;cold room;refrigerating room ;refrigerating compartment
-
你从附近的屠宰场买到20kg的牛心脏,放在冰上带回,在冷室或在冰上进行每纯化步骤。
You pick up 20 kg of beef hearts from a nearby slaughterhouse . You transport the hearts on ice , and perform each step of the purification in a walk-in cold room or on ice .
-
DGLS型洁净冷室的研制
Development of DGLS clean cold room
-
方法:大鼠置于4℃的冷室4h。
Methods : Rats were maintained in cold chamber at 4 ℃ for 4 h.
-
Texaco气化炉激冷室热质传递过程模拟
Process Simulation of Heat Mass Transfer of Quench Chamber in Texaco Gasifier
-
TEXACO气化炉激冷室下降管传热传质过程模拟
Heat & Mass Transfer Research on Descending Pipe of Quench Chamber in Texaco Coal Gasifier
-
结合J11280型卧式冷室压铸机,研究了基于Windows界面的压铸机电气控制系统的开发。
A new control system based on Windows OS for horizontal cold chamber die casting machine mode " J11280 " is designed .
-
根据铝合金壳盖铸件形状复杂、壁薄、外形尺寸小等特征,选用了J1125型卧式冷室压铸机。
J1125 type horizontal cold chamber die casting machine was used to produce the aluminum alloy housing of motorcycle based on its complicated shape , thin-wall and small profile dimension .
-
气化炉激冷室液位测量中的信号处理
Signal treatment in measurement of liquid level in gasifier quenching chamber
-
冷室压铸机用新型熔融金属输送系统
New Molten Metal Delivery System for Cold Chamber Die Casting Machine
-
冷室压铸机压射机构的改进
The Improvement of the Injection Mechanism of Cold Chamber Die Casting Machine
-
新型多喷嘴对置式气化炉激冷室的改造
Revamping Summary on the Chilling Chamber of the New Opposite-positioned Multi-nozzle Gasifier
-
进入20世纪以后,热室压铸机日渐成熟,冷室压铸机问世。
By 1920 , the earliest cold chamber die casting machine was published .
-
水煤浆气化炉激冷室带水问题的探讨
Theoretical Study on Entraining Water Problem in Quench Chamber of Coal-water Slurry Gasifier
-
全自动卧式冷室压铸机
Full automatic horizontal cold chamber die casting machine
-
可在4℃冷室或温度60℃和相对湿度80%的培养箱中使用。
Apply to4 ℃ cold chamber or60 ℃ incubator with relative humidity of80 % .
-
文中对二冷室的抽风形式及风量确定进行了较为详细的论述。
Exhaust type and exhausting volume determination for the chamber were discussed in detail also .
-
对气化炉激冷室的工艺特点进行了分析。
An analysis is made of the process characteristics of the quench chamber of the gasifier .
-
最佳加工贮藏初步工艺为:采用热榨加工工艺,在15-18℃冷室,无氧贮藏方式。
The optimal processing and storage were processed by hot-pressed juice and stored at 15-18 ℃, non-oxygen .
-
一冷室喷流速度分布及喷流冷却速度的研究
Study on the Distributions of Spray Flow Velocity and its Cooling Velocity for the Primary Cooling Chamber
-
液态金属在冷室压铸机压室中运动的理论与分析
Theory and Analysis of the Motion of the Liquid Metal in the Chamber of the Cold Die-casting Machine
-
通过对压铸件成型压力的计算,选择锁模力为6300kN的J1163型卧式冷室压铸机。
The horizontal cold chamber die casting machine with closed force of 6 300 kN has been selected by calculating filling pressure .
-
七屠体待运区(未设预冷室者应设之):应设置高架吊轨及送风设施。
Carcass holding area ( required when chilling room is not set up ) Overhead rails and forced air blower shall be equipped .
-
双室多功能真空烧结炉的冷室用于烧结后制品的快冷、气淬或油淬;
Cooling chamber of the multi-purpose two-chamber vacuum sintering furnace is used for quick cooling ( gas quenching or oil guenching ) aftr sintering .
-
分析了录音机芯飞轮压铸模的原设计失败的原因,重新设计了用于冷室压铸机的中心浇口、浮动分流的压铸模。
A new die-casting die fit on cold chamber die casting machine was redesigned in the part of the center gate and floating flow-distribution .
-
班亚的中心原则就是促进血液循环,我现在呆的是冷室,之前要在热室里接受火的折磨。
The central principle of thebanyais to stimulate the circulation , and this was thebasseyn , the cold room that preceded the ordeal by fire .
-
本文结合工程设计实践,对连铸机二冷室排蒸汽系统中的几个关键问题进行了分析。
Combined with practical engineering , the several key problems concerning the vapour exhausting system for CCMS secondary cooling chamber were discussed and analyzed in this paper .
-
模拟结果揭示激冷室内部的热、质传递的一些规律,提出了影响下降管内壁水膜覆盖的因素,影响下降管内部的换热因素以及灰渣的在激冷室内的流动特性。
The simulation results give some relationship curves of the heat and mass transfer inside the cooling chamber , and the author posts the effect factors on flow and heat transfer in the cooling chamber .
-
据此分析认为:卧式冷室压铸机冲头的慢压射过程是加速运动和匀速运动的组合,组合的结果直接影响压铸件的质量。
For this theory : the process of die-casting in the short sleeve of the cold die-casting is composed of invariable velocity and invariable accelerated motion , which result directly effect the quality of the cast .
-
压铸模具使用于卧式冷室压铸机,其型腔根据标准压铸试样的尺寸设计。其次,本文研究了在机械振动的条件下液体的对流规律。
The die mold matches horizontal cold chamber die casting machine , and its cavity is designed according to the die casting test bars . Secondly , this paper studies convection of liquid under mechanical vibration .
-
卧室冷室压铸机压铸时,压室底部被浇入的金属熔体所覆盖,熔体上部分至压室顶部的空间被气体所占据。
The bottom of shot sleeve is filled with melt by horizontal cold chamber die casting machine , when the beginning of the slow shot phase , volume on the melt to the top of sleeve is occupied by gas .