镀层厚度

镀层厚度的X射线衍射法测量

Measurement of Plating Thickness by X - ray Diffraction Method

在相同的阴极侧充氢情况下，比较了氢在低碳钢材料以及带有不同Zn-Ni-Cd镀层厚度的低碳钢组合材料中的扩散渗透情况，分析了Zn-Ni-Cd镀层对阻氢扩散的影响。

Permeation behaviors between low carbon steel and low carbon steel combinatorial material with different Zn-Ni-Cd plating thickness were compared under the same cathodic hydrogen charging , and the effect of Zn-Ni-Cd plating on hydrogen permeation resistance was analyzed .

X射线荧光法测试镀银铜线镀层厚度

Determination of Ag-coated Copper Wire Layer Thickness by X-Ray Fluorescence Method

X射线荧光法检测金属镀层厚度

Determination of Metal Plating Thikness by X Ray Fluorescence Method

铁基合金锡、锌镀层厚度的X射线荧光光谱快速测定

Rapid Measurement of the Thickness of Tin , Zinc Coatings on Steel by X-Ray Fluorescence

镀层厚度应与siC微粒粒度相当。

The thickness of coating should be suitable with the size of SiC particles .

碳纤维经过预处理，在酸性镀铜液中电镀，得到镀层厚度为1.3μm的Cu／Cf复合丝。

Through electroplating , copper coating about 1 . 3 μ m thick was formed on the carbon fibers .

用基体X射线衍射法测量了化学镀Ni-P合金的镀层厚度，并进行了误差分析。

Thickness of electroless Ni-P alloy plating has been measured by the substrate X-ray diffraction method and measurement error was analyzed .

XRF在外壳镀层厚度测试中的正确应用

Application of XRF to Coating Thickness Measurement of Metal Cases

根据镀层厚度与镀覆温度和时间的关系，得出碳化钛形成的激活能为94±7kJ／mol。

The calculated activation energy of TiC forming is about 94 + 7 kJ / mol.

但是，表面出现胞状结构，由于P含量分布不均，导致耐蚀性下降，P含量沿镀层厚度方向的梯度分布易形成针状蚀孔，引起镀层早期失效。

However , the anti-corrosion property deteriorates sometimes due to the appearance of cell-structrure in which the distribution of phosphorous is not uniform , and the gradient distribution of phosphorous along the vertical direction of the coating might lead to pitting attack resulting in early failure .

报导了利用镀光学薄膜的方法来改变镀层厚度，可以有效地将原来处于双模工作的1.3μmDFB激光器变为单模工作。

This paper reported that the method coating optical films can transfer the 1.3 μ m DFB laser from double mode operation into single mode operation .

Ni-W-B合金层在镀态时为非晶态结构，它的电阻率随钨含量的增加而增大，随镀层厚度的增加而降低。

Ni-W-B alloy is amorphously plated and its resistivity increases with the increase of W content , but decreases gradually with the increase of deposit thickness .

确定了脉冲电镀工艺参数，成功地制备适用于生产103Pd的Cyclone30加速器照射用铑靶，镀层厚度大于150mg/cm2。

The rhodium target , mass thickness is more than 150 mg / cm 2 , adapts to producing 103 Pd on Cyclone 30 accelerator .

结果表明预热温度为500～600℃、浸镀温度为1120～1135℃及浸镀时间4～6s时，可以获得理想的镀层厚度。

The results indicated that the maximum coating thickness was obtained with a preheating temperature of 500 ~ 600 ℃, bath temperature of 1120 ~ 1135 ℃ , and contact time of 4 ~ 6s .

另外，根据试验所取的七个树种的镀铜层厚度与施镀时间的关系趋势图可以得出在前10min内镀层厚度增加最快，施镀效果最好。

In addition , according to the trend of relationship between thickness of copper layer and plating time of seven species , the thickness of copper layer increase fastest in the first 10 minutes .

研究了发泡镍抗拉强度与其面密度的关系；通过对发泡镍的镀层厚度分布系数（TDR）的研究得知，如果TDR值大，表明发泡镍内部较脆弱。

And it studied the tensile strength of nickel foam noodle instead of the relationship between density . It has shown through studying the thickness distribution coefficient ( TDR ) of foam nickel coating that if the TDR value was large , the internal nickel foam was more fragile .

芯片焊锡镀层厚度对工程能力影响研究

Research into Impacts of Chip Solder-Plating Coat Thickness on Engineering Capability

热浸锌镀层厚度是检验热镀锌产品的一个基本且重要的指标，文中首先探明了热浸锌镀层厚度与时间、温度的影响；

The thickness of the hot-galvanized film is a important indication .

丝材连续镀金的镀层厚度

Controls of the Coating Thickness during Continuous Gold Electroplating for Wire

GB/T15717-1995真空金属镀层厚度测试方法电阻法

Test method for vacuum-deposited metal thickness & Electric resistance method

镀层厚度随电镀时间的延长而增加。

Coating thickness increases with the extension of electroplating time .

电镀层厚度对软磁材料性能影响的研究

The effects of electroplate thickness on the properties of soft magnetic substrate

热浸镀镀层厚度的动态控制方程

A kinetic controlling equation for coating thickness in hot dipping

通过趋肤深度，可以确定波导产品的镀层厚度。

Waveguide product plating thickness can be confirmed through surface effect depth .

用计算机程序来计算复合镀层厚度

A computer program used for calculating the thickness of multiple plating layers

检测片状电阻器镀层厚度的金相制样法

Metallographic specimen preparing method for measuring the cladding material ′ s thickness

蒸镀层厚度的电子探针测定法

A Method for Measuring Film Thickness with Electron Probe

铜包钢线导电性物理模型及镀层厚度计算

The Electric Conductivity Physics Model and Plating Thickness Calculation of Copper-clad Steel Wire

涂层、镀层厚度检测与测厚仪

Thickness Inspecting and Pachymeter of Coating and Plating Layer