接头形式

盾构隧道管片接头形式的探讨与选择

Discussion and selection of segment joint type of shield tunnel

压力钢管合拢焊缝接头形式试验研究

Experiment study on closured weld joint type of pressure pipes

对比不同接头形式的三板T型焊接头，W型的三板T型焊接头具有填充金属少，晶粒尺寸小、腹板热影响区窄等优点。

Compared to three-panel T-welded joints of different joint forms , W-shaped three-panel T-welded joints had advantage with less filling metal , small grain size and narrow-web heat-affected zone .

提出了适合于CO2焊特点的接头形式，该接头形式在保证焊接质量前提下，减小了对接焊的坡口角度及角焊缝的焊脚尺寸，可以提高焊接生产率，降低成本。

The joint shapes suited for CO_2 welding are designed Under which weld quality is still assured but the groove angle and size of fillet weld are reduced . By ways of these the productivity is increased and cost decreased .

钻井用石油套管接头形式的研究开发

R & D of Oil Casing Connection Type for Well-drilling Service

钢丝绳芯强力皮带接头形式的选择与施工

The Selection and Construction Form of Steel Cable Strong Belt Joint

盾构法隧道管片接头形式研究及其优化

Research and Design Optimization on the Joint of Shield-tunneling Segment

一种新型混凝土防渗墙接头形式的初步研究

Study on A New Kind of Joint Type of Concrete Cut-off Wall

沉管隧道的一种最终接头形式及施工方法

A type of final joint of immersed tube tunnels and its construction method

地下连续墙接头形式及其渗漏的防治措施

Joint Forms of Underground Continuous Walls and Protection and Treatment Measures of Their Leakage

接头形式对胶接强度的影响

The Effects of Joint Forms on Bonding Strength

接头形式对采用名义应力幅值Δσ表示的疲劳强度有较大影响；

Fatigue life based on nominal stress range Δσ is affected by different joint geometries .

接头形式对于玻璃纤维增强聚碳酸酯&钢粘结的影响

Influence of Fitting Form on Creep Rupture Behaviour of Fibre Glas Reinforced Plastic / Metal Adhesive Joints

接头形式及装配顺序对车身装配偏差影响的研究

Research on the effect of deviation of vehicle body assembly affected by form of joint and assembling sequence

由于接头形式不同，接头参数的选取对模型计算结果的影响很大。

Because the joint has different forms , the selection of joint parameters has an enormous effect on calculation results .

转子支架的工地焊缝中立焊缝采用搭板连接的接头形式。

Stiffener connection is used as the joint form for the vertical position welds in site wedling of rotor spider .

研究了不同搭接接头形式，胶粘剂毛边和拉伸剪切强度的测试方法对拉伸剪切强度的影响。

The effects different joint forms , queer out and the measuring ways on tensile sheer strength are studied in the paper .

结果表明，合理选择焊接接头形式和焊接工艺可以成倍地提高结构的疲劳寿命。

The results show that the proper selection of modes of welded joints and welding technologies can double improve the fatigue life of structures .

通过优化工艺参数获得了激光-TIG双面焊接的三种典型的接头形式，对比了熔透条件下的双面电弧焊接头的力学性能。

Three typical welding joint were obtained . The mechanical property of double side arc welding was investigated in contrast to the laser-TIG double side welding .

用国际焊接学会推荐的方法进行统计处理，并和相同接头形式结构钢的疲劳强度进行了比较。

Moreover , the test data were statistical treated with the method recommended by IIW and compared with fatigue strength of structural steel with identical joint type .

本文所提出的模拟分析方法可以推广到各种尺寸规格、各种接头形式的焊接过程的计算分析中去。

The proposed simulation method in this paper can be extended to the calculation analysis of joints with variety of sizes , various forms in the welding process .

工业考核证实：与传统接头形式的钎头相比，螺旋副连接钎头凿岩速度可提高28.5%￣42.4%。

Industry experimentation proves that the rock-drilling velocity of screw-pair jointing bit is higher than that of traditional jointing form bits , mounting 28.5 % ~ 42.4 % .

基于激光透射焊接的原理和过程，采取搭接接头形式进行焊接，同时焊接关键技术和难点也被考虑。

Based on the principle and process of laser transmission welding , the lap joint form was taken and the key technology and difficulty of welding were also considered .

然后，利用知识规则进行杆件方位的智能确定和杆件拼接接头形式的自动选择。

Based on the knowledge rules of machine frame structure , orientations of frame members are determined by reasoning , and the joint type among structural elements is selected automatically .

以搭接接头形式为例，采用最坏情况法分析了装配顺序对最终装配偏差的影响。

Taking the form of lap joint as an example , the effect of final assembling deviation affect by the assembly sequence was analyzed by adopting the method of worse condition .

重点阐述了内孔焊的接头形式、焊接设备、工艺装备、焊接工艺参数以及具体实施过程中应注意的问题。

The joint design , welding equipment , fabrication equipment and welding parameters for inner-hole welding as well as difficulties which should be paid attention to during the fabrication are mainly described .

针对奥迪轿车消音器的材料、结构及接头形式，研制了适用于消音器焊接的熔化极气体保护自动焊设备，并对焊接工艺进行了研究。

In order to solve Audi car muffler welding problems , a MIG automatic welding process and equipment arc developed which is suitable for the material , structure and joint type of the muffler .

焊接是铁路车辆的主要连接方式，铁路货车车体基本上都是用板材焊接而成的，其中包含了各种接头形式，结构越多接头形式越复杂。

Welding is the main connection of railway vehicles , Railway Vehicle basically welded sheet metal , which contains a variety of joint type , joint type structure , the more the more complex .

但是，运行速度的提高、载荷的增大、频率范围的扩大，尤其是复杂的焊接接头形式使得转向架构架的承载状况变得十分恶劣。

However , with the raising of operation speed , and increasing of loads and frequency ranges , and especially the complicated types of weld joints , the load conditions of railway bogies become even worse .

分析结果表明，车身装配过程中，在不增加额外费用的前提下，零件之间采用合理的接头形式和装配顺序，同样能达到降低最终装配偏差的目的。

The result of analysis shows that under the prerequisite of not increasing additional expenses , employing reasonable joint form and assembly sequence among components could also reach the same aim of reducing the final assembling deviation .