铝合金板

铝合金板表面形貌模型的研究

Research on the Topography Model of Aluminum Alloy Sheet Surface

铝合金板温成形关键技术的研究

Study on Key Technologies of Aluminum Alloy Sheet Warm Forming

本文对受拉伸载荷的铝合金板被强连续波CO2激光照射时的热机械响应进行了报导。

Thermomechanical response of Al plates under tension to high energy CW CO2 laser radiation is discussed .

GLARE层板的压缩和弯曲性能受铝合金板和玻璃纤维的性能共同影响。

The compression and flexure of GLARE are affected by both aluminum and glass fiber .

纳米SiO2/碳纤维增强复合贴片修复损伤铝合金板力学性能研究

Research on Mechanical Properties of Cracked Al Alloy Plate Repaired by Nano-SiO_2 / CF ( Carbon Fiber ) - reinforced Composite-patch

用ODF图的诠释图分析铸轧3004铝合金板织构

Analysis of Texture of 3004 Alloy Sheet Produced from Continous Casting Sheet by Explanation ODF Figure of Cubic Materials

用高温应变计和热偶计等诊断技术，研究连续波氧碘化学激光（CW／COIL）与铝合金板作用产生的激光热应力。

The laser thermal stress induced in the aluminum alloy plate irradiated by CW / COIL were investigated by high temperature straingauge and thermocouple gauge and other diagnostic techniques in this paper .

对厚度为3mm的LF2铝合金板成功地进行了搅拌摩擦连接。

The aluminum alloy LF 2 ( 3 mm thick ) was successfully friction-stir welded .

为分析E－400铝合金板翅换热器A流道的爆破失效原因，对A流道中的残留物质进行了各种化学和X射线分析，进行了A流道实物模拟爆破试验。

In order to analyze the reason of exploding occurred in the stream A of E-400 Al-Alloy Plate-Fin Heat Exchanger , a simulated exploding experiment is carried out and various chemical and X-ray analysis for substances obtained fron the stream A are made .

采用搅拌摩擦焊方法对厚度为20mm的2519高强铝合金板进行了单道对接焊试验，并对焊缝的微观组织、力学性能及断裂特性进行了分析。

Friction-stir welding of 2519 high-strength aluminum plate in 20 mm thickness was completed by a single pass .

上述结果表明，在评估汽车用铝合金板的拉深性能时，使用xb值为评价指标最为准确。

The results above indicate that it is much more exact to evaluate drawability of automotive aluminium alloy sheets by means of the values of x_b .

利用初始单系滑移模型和{123}〈634〉织构组分体积分数可以快速而准确地计算出3104铝合金板的应变比（r）值，并兼顾到非织构因素的影响。

According to the volume fraction of the { 123 } 〈 634 〉 texture , the r value of the 3104 aluminum sheets was calculated rapidly and accurately based on the initial single slip model , while some other effect factors beside texture were also included .

以深冲铝板R值的在线检测为应用背景，塑性变形滑移系开动的过程为出发点，分析了初始滑移系选取的方式，并计算了不同取向3104铝合金板的初始R值。

In consideration on the on-line R-value measurement of aluminum deep drawing sheets , the selection of initial slip systems was analyzed according to the activation process of the slip systems during plastic deformation . Initial R values of the 3104 aluminum sheet in different directions were calculated .

铝合金板LY12～M12的实验研究表明：随着塑性予应变的增加，将依次出现各向同性强化、运动强化以及组合强化。

A study of aluminium alloy sheet shows that , the isotropic hardening , the kinematic hardening and the combinative hardening would occur successively as the plastic prestrain increasing .

本文是针对320C铝合金板翅式机油换热器在性能测试过程中，焊缝的断裂失效而进行的。

In this dissertation , based on the fracture failure of performance tests of 320C Al alloy heat exchanger , several reasons were analyzed .

铝合金板淬火残余应力的拉伸消除方法

Stretch Method to Releve Residual Stress in a Aluminium Alloy Plate

温成形中铝合金板成形极限图的预测研究鱼尾形臂板，预告臂板

Prediction of forming limit diagram of aluminum sheet at elevated temperatures

模具温度对铝合金板拉深性能的影响

Effect of tools temperature on formability of aluminium alloy sheet

铝合金板带材固溶淬火技术

Solution and Quenching Technology of Aluminium Alloy Plates and Strips

复合材料补片胶接补强铝合金板残余热应力研究

Thermal Residual Stresses in Bonded Composite Repair of Aluminum Substrates

变压边力条件下铝合金板的成形窗口

Formability window of aluminium alloy sheet at variable blank-holder force

铝合金板的弹塑性临界屈曲应力

The elasto - plastic critical stress of aluminum alloy plates

铝合金板料的新淬火状态与高压柔性成形技术

As_Quenched Al Alloy Sheet and High Pressure Flexible Forming Technology

5182铝合金板温成形工艺及摩擦学特性的研究

Study on Tribology Characteristics Warm Forming Technology of 5182 Al Alloy Plate

汽车用铝合金板拉伸性能与成形能力的相关性

Correlation between uniaxial tension properties and formability of automotive aluminium alloy sheet

润滑条件下铝合金板成形模拟中摩擦模型的研究

Research on the Friction Model for Lubricated Aluminum Alloy Sheet Forming Simulation

铝合金板料深冲成形的晶体塑性有限元模拟

Simulation of the Deep Drawing of Aluminum Sheet Using Crystal Plasticity FEM

铝合金板橡皮成形简化数值分析模型研究

Simplified Numerical Analysis Model of Rubber Forming Process for Aluminium Alloy Sheet

中间退火对3003铝合金板组织和晶粒度的影响

Effect of medium annealing on microstructure and grain of 3003 aluminum alloy

覆盖件用铝合金板料滚压翻边方法的研究

Research on Flanging of Aluminum Alloy Sheet for Auto-Body Panels