活塞

本文分析了活塞式RTM机存在的一些缺陷。

The defect of plunger type RTM machine is analyzed in this paper .

配置有高强度烤漆钢板水箱，SUS304不锈钢活塞杆及双头均可活动的高压管。

Equipped with the steel water tank which is of high strength baking finish , stainless steel plunger ( SUS304 ) and pressure pipe with two moveable ends .

活塞上涂了一层石墨以减小摩擦力。

The pistons are graphite-coated to reduce friction .

活塞在蒸汽压力下运动。

The piston moves by steam pressure .

活塞通过连杆与驱动轴相连。

A piston links to a drive shaft by means of a connecting rod .

他们改用活塞发动机。

They use a piston engine instead .

自动阻风门包括一个恒温控制弹簧和一个真空活塞

The automatic choke includes a thermostatic spring and a vacuum piston .

泵使用阀和活塞。

A pump uses valves and pistons .

本文分析了钻井法凿井中所出现的钻井活塞效应问题及带来的危害

This paper analyses the piston effect problem in dellling shaft sinking method and its detriments .

基于DSP的液压双自由活塞发动机控制系统的研究

Research on Dual Piston Hydraulic Free Piston Engine Control System Based on DSP

线阵CCD检测活塞环闭口间隙的新方法

New Method of Measuring Piston Ring End Gap Clearance with line Matrix CCD

该文基于对MR阻尼器流变特性的力学分析，研制了一种活塞表面刻有螺旋凹槽的新型MR阻尼器。

Based on mechanical analysis on rheological characteristics of MR damper , a novel MR damper with helix slotted plunger is developed .

CFD方法在预测柴油机内冷通道活塞温度分布方面的应用

Application of CFD to Predict Temperature Distribution of Diesel Engine Piston with Inner Cooling Gallery

基于UG的内燃机活塞机构虚拟装配和运动仿真

Virtual assembly and movement emulation for piston mechanism of internal combustion engines based on UG

结果表明，整个工艺过程控制稳定，化学镀Ni－P活塞环可以取代镀Cr环。

Re sults show that the whole plating process could ha controlled steadily and the Ni-P Chemical plating rings could replace the chromium plating rings .

就三种回收方案中，对液压回收方案的液压回路进行了设计，并用MATLAB程序对活塞回收过程进行了动态仿真。

Among three projects , the hydraulic pressure loop is designed and the dynamic simulation for piston reclaiming process is performed with MATLAB program .

高强耐热Al-Si活塞合金的研究

Study on High Strength Heat-Resistant Al-Si Piston Alloys

基于APDL的活塞热力耦合程序开发

Development of Piston Heating-power Coupling Analysis Procedure Based on APDL

发动机活塞销孔精镗加工用PCD镗刀和精密微调镗杆

PCD Boring Tool and Fine Adjustment Boring Bar Used in Precision Finishing Pinhole of Engine Piston

要再扣篮的话，篮网恐怕要不行了。篮网与活塞晋级nba东区第二轮比赛

The goal will probably not withstand another slam dunk . Nets and Pistons Advanced to Second Round of NBA Eastern Conference

采用有限元ANSYS软件，分析了相同活塞有效长度下的单线圈与双线圈结构磁流变阻尼器的磁场分布情况。

The magnetic distribution of the single-coil and dual-coil magnetic rheological dampers with the same effective piston length was analyzed by using the finite element ANSYS software .

针对中凸变椭圆活塞横向和纵向复杂型线的特点，提出了采用MATLAB曲线拟合工具对活塞的轮廓线进行曲线拟合。

Based on the character of the middle-convex and varying ellipse piston with complex transverse and longitudinal section contour , a method using MATLAB to fit piston skirt curve is given in this paper .

采用UG软件进行活塞的三维实体建模，并根据实际生产设计出三种浇注系统。

3D solid modeling of piston should be completed by UG software and design three kinds of runner and gate systems according to the actual production .

ADIA活塞直径

A dia piston diameter

订货的场合，如果对活塞杆头、油缸盖的U形环的宽度、销子的直径等尺寸方面另有要求时，建议采用能够利用的本公司现有的模锻件。

If any other requirements for piston rod head , U type ring width of cylinder lid , and diameter of pin are needed when placing an order , it is recommended to use our existing forged pieces .

并设计了东风EQ140汽车活塞的保温冒口。

Meanwhile , an insulating riser for piston of Dong-Feng EQ140 automobile was designed .

阐述了三缸机械液压约束活塞发动机（HCPE）工作原理，建立了系统工作过程的微分方程。

The working principle and structure of3-cylinder hydraulic confined piston engine ( HCPE ) is put forward , and the working process differential equations is constructed .

在“电子节目指南”（两个下巴）和“ETG的”（三下巴）爪平行线利用了双动活塞和摇臂的设计。

The " EPG "( two jaw ) and " ETG "( three jaw ) parallel gripper lines utilize a double acting piston and rocker arm design .

利用SRV高温摩擦磨损试验机模拟发动机运行态条件，考察了五种活塞环在GF-3全配方发动机油润滑下的摩擦学性能。

The tribological performance of five kinds of piston rings when lubricated with GF-3 fully-formulated engine oil was investigated on a SRV high temperature friction and wear tester .

结合挤塑模和轻型客车的虚拟装配、活塞连杆机构及发动机的运动过程，实现了基于真实动画感的VPD环境下的产品虚拟装配及虚拟工作过程仿真。

Visual product virtual assembly and virtual work under VPD environment are realized , through the virtual assembling examples of a plasticator and the light bus , and virtual working simulation of a piston valve gear and a engine .