固体润滑

新型Ni－Cu－P／MoS2固体润滑镀层优化试验研究

Optimization of a new type Ni-Cu-P / MoS_2 solid lubrication plating layer produced by brush plating

基体状态对FeS层固体润滑性能的影响

Influence on the Solid Lubrication of Iron Sulfide Layer from Substrate State

本文研制出一种新型NiCuP／MoS2电刷镀固体润滑复合镀层。

This Paper developed a new kind of Ni-Cu-P / MoS2 solid lubricating deposit by brush plating .

PTFE固体润滑膜技术及其应用

Technique and application of PTFE solid lubricating film

制备工艺对MoS2粘结固体润滑涂层微动磨损寿命的影响

The Influence of Preparation Processes on Fretting Wear Life of MoS_2 Bonded Solid Lubricating Coating

一种硼改性FB酚醛树脂基粘结固体润滑涂层摩擦学性能的研究

Tribological Behavior of FB-based Bonded Solid Lubricating Coating Modified with Boron

原子氧对MoS2/PI粘结固体润滑涂层真空摩擦学性能的影响

Effect of Atomic Oxygen on Tribological Properties of MoS_2 / Polyimide Bonded Lubricating Coatings in Vacuum

紫外辐照对MoS2/酚醛环氧树脂黏结固体润滑涂层摩擦学性能的影响

Effect of Ultraviolet Irradiation on the Tribological Properties of MoS_2 / Phenolic-Epoxy Resin-based Bonded Solid Lubricant Coatings

湿度、温度及润滑油对粘结MoS2固体润滑涂层微动磨损寿命的影响

Influence of Relative Humidity , Temperature , Oil Lubrication on the Fretting Wear Life of Bonded Solid Lubricant Coating

聚四氟乙烯（PTFE）是优良的固体润滑材料，其摩擦系数低，化学稳定性好。

Polytetrafluoroethylene ( PTFE ) is an excellent solid lubricating material , with low friction coefficient , good chemical stability .

FeS固体润滑涂层的结构分析及磨损行为比较

Microstructures and wear-resistance behaviors of ferrous sulfide coatings

两步法制备固体润滑FeS薄膜的摩擦磨损性能研究

Study on the Tribological Properties of FeS Solid Lubrication Films Prepared by Two-Step Method

渗硫参数对氮碳共渗表面形成FeS固体润滑层的影响

Effect of Sulphurizing Parameters on the Formation of FeS Solid Lubrication Layer on Nitrocarburized Surface

通过溶胶-凝胶法在45钢基体上制备了厚约500μm的FeS固体润滑涂层。

The FeS solid lubrication coating with 500 μ m thick was prepared by a sol-gel method on the 1045 steel .

利用等离子喷涂技术在GCr15钢表面制备了纳米-亚微米MoS2固体润滑涂层。

Nano - and submicron-structured MoS_2 coating was deposited by atmospheric plasma spraying .

通过两步法，即射频溅射Fe膜与低温离子渗硫复合处理工艺，在非黑色金属（单晶硅）表面得到了固体润滑FeS薄膜。

Solid lubrication FeS films were prepared on non-ferrous metal ( Si ) surface by two-step method , namely composite processing between radio-frequency sputtering Fe and low temperature ion sulfuration .

纳米WS2润滑晶体是一种性能优良的新型固体润滑材料。

Nano WS_2 crystal is a kind of solid lubrication material with excellent lubrication performance .

含纳米LaF3的固体润滑涂层摩擦学及抗腐蚀性能研究

Effect of Nanometer Lanthanum Fluoride as a Filler on the Tribological Behavior and Corrosion Resistance of a Boned Solid Lubricating Coating

FeS作为固体润滑材料的突出代表，由于其疏松多孔易滑移，硬度很低，剪切强度很小，有着良好的降低摩擦系数的特性以及良好的润滑性能，有着广泛的应用前景。

FeS is a typical solid lubricant . It can reduce the friction and wear effectively because of its porous structure with low hardness , shear strength and good lubricating property .

PF-1粘结固体润滑膜作为耐油预涂膜的性能考察

A Study on the Performance of PF-1 Solid Lubrication Film as Oil-Compatible Precoating Film

通过对FeS固体润滑层表面微观形貌的观察，初步分析了渗硫条件和氮碳共渗表面对其上FeS固体润滑层形成的影响。

The effect of sulphurizing parameters and nitrocarburized surface on the formation of FeS solid lubrication layer was investigated through observing the surface morphology of the FeS solid lubrication layer under SEM .

用球盘式摩擦试验机及原子力显微镜在大气中常温下对YBa2Cu3O7（YBCO）高温超导试样的宏观和微观摩擦学特性进行了研究，并与Cu基固体润滑复合材料进行比较。

The micro and macro tribology characters of sintered YBa_2Cu_3O_7 ( YBCO ) in the air were investigated by using ball on disc tester and atomic force microscope ( AFM ), and a comparison with Cu based solid lubricant composite was prepared .

磷嗪X-1P添加剂对硬脂酸钾固体润滑薄膜摩擦学性能的影响

Effect of X-1P as Additive on the Tribological Behavior of Potassium Stearate Films

用销-盘实验机研究了Teflon固体润滑涂层在高速（5.6m/s）、重载（初始接触应力400MPa）条件下的摩擦磨损性能。

The tribological properties of Teflon layer under high speed ( 5.6m / s ) and high pressure ( 400MPa ) were studied on pin-on-disk tester .

分别利用等离子氮化技术和离子束增强沉积（IBED）技术使钛合金表面获得硬质抗磨层和MoS2，MoS2Ti固体润滑膜层。

Plasma nitriding and ion beam enhanced deposition ( IBED ) films including TiN hard coating and MoS_2 , MoS_2-Ti solid lubricating films were used to treat titanium alloy .

结果表明，通过摩擦反应在表面形成固体润滑膜，是改善SiC-Si复相陶瓷干摩擦性能的有效途径。

It was shown that solid lubrication film formed in friction reaction was efficient for improvement of friction and wear property of the SiC-Si .

因此，镀层硬度是依摩擦温度的高低及其在镀层中的梯度分布而呈现出不同的分布特征，从而揭示了Ni-P/WC复合镀层在高PV值条件下显示良好固体润滑性能的原因。

Therefore , the composite plating layers show different hardness distribution along with the changes of friction temperature and its gradient distribution . Thus , the reason for Ni-P / WC composite plating layer presents good solid lubrication properties under high PV value condition can be revealed .

氮碳共渗表面细小的缺陷和凹坑为硫化物提供了形核的活性中心，利于形成以FeS相为主的较厚的FeS固体润滑层。

The results show that the mass of small imperfection and indentation on nitrocarburized surface provides plentiful nucleation active center for the sulphide formation , which is of benefit to formation of thicker FeS solid lubrication layer with the main phase of FeS .

利用球磨方法得到用于喷涂的、粒度约40μm的硫化亚铁（FeS）微颗粒，再用超音速火焰喷涂的方法在45钢表面制备了固体润滑硫化亚铁涂层。

The powder of FeS , with granularity of 40 μ m for spraying , was prepared by ball-mill method , and then the FeS powder was sprayed by ultrasonic flame spraying to form the solid lubrication FeS coating on the 45 steel surface .

WS2作为一种新型的优秀固体润滑材料在某些方面的表现要优于传统的MoS2薄膜，因此人们开始越来越多地关注WS2在摩擦学方面的应用。

As a late-model excellent solid lubrication films tungsten disulfide films performance is better than classical molybdenum disulfide films in some aspects . So the tribological behavior of WS2 films has been paid more and more attention .