悬臂

BP神经网络在悬臂柱损伤位置识别中的应用

Application of BP neural networks to damage identification of cantilever column

~（60）Co集装箱检测车悬臂振动分析

Analysis of cantilever vibration of ~ ( 60 ) Co container inspection vehicle

在他的设计中，悬臂梁伸出太多，不能平衡

In his design the beam cantilevers out far for balance .

非悬臂梁末端种植体齿槽骨吸收与前部种植体齿槽骨吸收比较差异无显著意义

More crest bone absorption were noticed at the implants near cantilevers .

PLC控制液压同步顶升系统在连续钢箱梁悬臂架设施工中的应用

Application of PLC-Controlled Hydraulic Sync Jack-up System to Cantilever Erection of Continuous Steel Box Girder

扭梁悬臂梁支撑的扭摆式MEMS永磁双稳态机构

A Teeterboard Pattern MEMS Permanent Magnet Bistable Structure Supported by Torsion and Cantilever Beam

基于力学描述的MEMS悬臂梁系统级动态模拟方法

Method of System-level Dynamic Simulation for A MEMS Cantilever Based on the Mechanical Description

为了设计出导电的Ni微变截面悬臂梁，采用了基于成熟的电镀技术的微电铸工艺。

Micro-electroplating based on the mature electrodepositing technology was applied to design conductive Ni micro-cantilever with different cross-section .

基于空心铝合金悬臂梁的FBG压力解调的研究

Based on the Hollow Aluminum Alloy Cantilever Demodulation of FBG Pressure Research

运用压电微悬臂梁相关理论，分析了高谐振频率的PZT压电微悬臂梁的信号特征。

Signal characteristics of high resonance frequency PZT cantilevers are analyzed with the theory of piezoelectric micro-cantilevers .

本文介绍一种低g值双悬臂梁式硅压阻式加速度传感器新结构，通过理论分析与计算，说明该结构的硅压阻式加速度传感器具有良好的输出性能。

A double beam structure piezoresistive accelerometer is presented in this paper , it is prove that the accelerometer has high output properties through theoretical analysis and calculation .

探讨了零初始位移法和切线初始位移法之间的关系，采用ANSYS有限元软件对悬臂结构进行了两种位移求解法之间关系的验证。

The relationships between zero-initial-displacement method and tangent-initial-displacement method are discussed and verified in allusion to cantilever structures with the finite element software ANSYS .

就MEMS薄膜断裂强度的测试提出了一种新的测试结构，该结构由待测梁（悬臂梁）和驱动源（V形热执行器）两部分组成。

This paper presents a new structure for measuring MEMS films fracture strength . The test structure incorporates a V thermal actuator and a cantilever .

同时，在悬臂浇注的PC斜拉桥施工控制中，立模标高很容易受到多方面因素的影响，特别是中间索力和前支点挂篮对立模标高的影响不容忽视。

Meanwhile , the formwork placing elevation is influenced by several factors , especially the influences caused by mid cable force and preceding fulcrum traveling carriage cannot be ignored .

对附加可控约束阻尼层的悬臂矩形板进行了实验与理论建模，详细分析了模型中的不确定性，并进行了H∞鲁棒振动控制的数值仿真与实验研究。

The uncertainties in theoretical model of the plate are analyzed through calculation and experimentation . H ∞ robust vibration control is then studied by employing the mixed sensitivity design method .

考虑实际微结构表面粗糙度对粘着特性的影响，利用表面力以及表征微尺度粘着弹性接触理论的粘着数对微机械中典型的微悬臂梁结构的剥离数（peelnumber）进行修正。

Considering the effect of surface roughness on the adhesion of microstructures , the surface force and adhesion parameter characterizing the micro-scale adhesive contact were used to modify the peel number .

HLB型悬臂液下泵在锌电解工序中的应用与改进

Use and Improvement of the HLB Type Liquid Descends Pump in the Electrolytic Application in Zinc

结果表明：通过合理分割电极为传感区和执行区来实现自感知执行的压电SSA，能有效地对悬臂梁的振动状态进行检测和控制。

It is clearly showed that space-sharing piezoelectric SSA is effective to detect and suppress vibration in the results of vibration control experiments .

执行了用铝、GFRP和铝GFRP混合材料制成的悬臂管试验。

The bending test of cantilever tubes that was fabricated with aluminum , GFRP and aluminum / GFRP hybrid by co-curing process will be performed .

本文应用Hamilton原理，推导了全覆盖双层约束阻尼悬臂梁的运动方程，对模型进行了实验验证；

In this paper , The differential equations of motion of a fully covered damped sandwich-type cantilever beam are derived employing Hamilton 's principle . The model is validated experimentally .

利用NI的PCI6221数据采集卡，通过LabView系统分析压电薄膜的传感特性和频率特性，并在此基础上设计并调试了压电悬臂梁差分电荷放大电路及微电流放大电路。

Sensing and frequency characteristics of piezoelectric-film have been analyzed using the NI-DAQ PCI 6221 by Lab VIEW system . Based on the analysis above , sensing circuits ( differential charge amplifier and micro-current amplifier ) have been designed and debugged .

基于电纺的PANI纳米纤维，制作了悬臂梁结构的静电执行器，并测试了PANI悬臂梁在静电力作用下的位移。

The electrostatic actuator with cantilever structure was fabricated based on electrospun PANI nanofiber , and the displacement of PANI cantilever beam under electrostatic force was measured .

给出由三角函数和多项式组成的近似挠度函数w（x，y）和应力函数F（x，y），它们满足矩形悬臂板的部分边界条件。

In this peper , the approximate deflection function ( x , y ) and stress function F ( x , y ) which consist of trigonometrical function and polynomial expression are selected . They satisfy part of boundary conditions .

所设计的测力传感器能同时测定正压力和摩擦力，其悬臂由一组相互垂直的平行弹性钢片组成，其解耦特性经有限元软件ANSYS得到证明。

The force sensor is able to measure normal force and friction force simultaneously . The cantilever of force sensor is made up of orthogonal elastic sheet steels whose decoupling characteristics are proved under finite element analysis software ANSYS .

系统分析了边界条件、荷载类型、悬臂翼板长度和曲率半径R等因素对直线和曲线矩形截面箱梁剪力滞后效应的影响，明确了上、下翼板的应力变化规律。

The variation in the shear lag effects on straight and curved rectangle box girders , caused by the changes of factors such as natural boundary conditions , types of loading , lengths of cantilever flanges and curvature radius R , is discussed systematically .

用电镀工艺在不锈钢基体上镀制了Cu，Ag，Ni膜和Ti基体上制备了Ni膜，并用悬臂梁法和X射线法测量了膜中的残余应力。

Cu , Ag and the Ni films on stainless steel bases and Ni film on Ti substrates are prepared by using electroplating . The cantilever beam method and X ray diffraction are used to measure the internal stresses in the films .

论文的主要内容及结果如下：1.采用UV-LIGA工艺制备金属悬臂梁型和简支梁型三维MEMS探卡结构。

The main contents and results are listed as follows : 1 . Study on metal cantilever type and simply supported beam type 3D MEMS probe cards fabricated by UV-LIGA technology .

基于结构有限元分析软件ANSYS得到的结构位移模态分析数据，针对具有不同损伤状况的悬臂梁进行了结构曲率模态分析。

The curvature modes of a cantilever beam with two types of notch are derived from its displacement modes obtained by finite element analysis using software ANSYS . Caused by damage , the change of natural frequencies and displacement modes is small .

针对能代表MEMS器件特征的悬臂梁结构，采用了SPICE中标准多项式受控源的形式建立悬臂梁的多模态小信号等效电路宏模型。

Aimed at the cantilever beam structure which can stand for the characteristic of MEMS devices , standard polynomial controlled sources of SPICE are introduced to build multi mode small signal macromodel of equivalent circuit for cantilever beam .

在外力的作用下，用SPICE软件对此悬臂梁宏模型和外加电路进行了系统级的模拟，得到分布参数的力传感器的输出电压幅频特性曲线；

Under the force loaded outside , the output voltage amplitude frequency response characteristic of distributed parameter force sensor is presented , by the system simulation to the cantilever beam macromodel and periphery circuits with SPICE .