进气歧管

福特电喷进气歧管金属型重力铸造工艺

Inlet Manifold for Ford Car in Permanent Mold Casting

铝合金进气歧管铸件的金属型铸造

Aluminum Alloy Inlet Manifold of Micro-car in Metal Mold Casting

Air（初三适用）注塑成型工艺是开发塑料进气歧管的重要环节。

The injection molding is an important tache to exploit plastic air intake manifold .

介绍了消失模法生产进气歧管的工艺过程、过程控制参数及主要设备。生产表明，采用EPC法生产进气歧管，既提高了生产率又改善了铸件品质。

The process , the parameters of procss control and the main equipment for production of the manifold by EPC process are introduced .

空气中的一部分co2分子会吸引那些自由电子。当进气歧管有真空存在时，真空便向上吸引膜片。

A few percent of the CO2 molecules in the air manage to find such electrons . When there is vacuum in the intake manifold , the vacuum holds the diaphragm up .

国内某款乘用车V型6缸发动机进气歧管（319.0）开发过程中，屡屡出现缩孔、气（针）孔等铸造缺陷，严重地影响了供应商的正常供货以及整车厂产能的提升。

During the developing process of one V-6 type engine intake manifold with 319.0 alloy , many defects as shrinkage and pin hole occurred frequently , which hindered its normal supply and thus affected the OEMs productivity .

第二部分用STAR-CD流体软件对可变式进气歧管进行空气流动数值模拟分析。

The second part carries on the air fluid simulation analysis of variable intake manifold with the STAR-CD fluid software .

运用气体动力学原理，结合计算机辅助设计（CAD）方法设计了CF4G27降高型发动机的进气歧管。

The intake manifolds for CF4G27 low set engine was designed in accordance with the principle of gas dynamics and CAD ( Computer Aided Design ) .

电喷汽油机进气歧管的CAD/CFD设计

Application of CAD / CFD to Intake Manifold of EFI Engines

发动机可变长度进气歧管系统的优化设计研究

Study on Optimization Design of Engine Variable Length Intake Manifold System

镁合金进气歧管消失模铸造工艺的试验初探

Exploration of the LFC Process for the Magnesium Alloy Intake Manifold

本文就是研究开发塑料进气歧管方法的部分内容。

This paper belongs to a part of exploiting method .

塑料进气歧管注塑过程仿真分析

Simulation Analysis of Injection Molding on Plastic Air Intake Manifold

高性能的发动机对进气歧管的设计也提出了更高的要求。

High-performance engine also needs higher designment requirment of the intake manifold .

进气歧管结构对进气不均匀性影响的仿真研究

Simulation Study on Charge Unevenness for Air Intake Manifold Construction

发动机塑料进气歧管振动试验失效分析与改进研究

Vibration Test Failure Analysis on Engine Plastic Intake Manifold and Improvement Study

目前，国内设计制造塑料进气歧管的技术还不过关。

Now domestic companies have no ability to design it .

电喷发动机进气歧管设计开发新方法

A New Designing and Developing Method for Intake Manifold of EFI Engine

拆下进气歧管、叉臂轭护圈，并对正叉臂轭。

Remove intake manifold , yoke retainer and aligning yokes .

发动机进气歧管的塑料化已是全球性的趋势。

The plastic intake manifold is already a global trend .

注塑工艺对增强尼龙进气歧管纤维分布的影响

Effect of injection process on fiber distribution of reinforced nylon air intake manifold

基于快速原型技术的进气歧管模具制造

Mould Manufacturing for Inlet Manifold Based on Rapid Prototyping

汽油机塑料进气歧管型腔设计方法研究

Research on Design Method of Plastic Air Intake Manifold Cavity for Gasoline Engine

发动机进气歧管压力传感器的标定与建模研究

The Study of Calibration and Modeling on an Engine Intake Manifold Pressure Sensor

化油器发动机进气歧管电喷化的设计开发

Design of Intake of Engine Equipped with Carburetor for EFI Technology of Engine

汽车进气歧管用塑料及其成型方法

Plastics and Moulding Processes for Automotive Air Intake Manifold

基于可装配性分析的塑料进气歧管设计研究

Research on Plastic Air Intake Manifold Based on DFA

汽车进气歧管真空注型材料选用和工艺探讨

Material selection and process discussion of vacuum casting in automotive air intake manifold

进气歧管消失模铸造温度场及充型特性的研究

A Study on EPC Temperature Field and Filling Property of Automobile Al Ingate

汽车发动机进气歧管压力传感器关键技术的研究

Research on Some Key Techniques of Manifold Absolute Pressure Sensor in Vehicle Motor