边槽

碳纤维增强卷边槽形钢柱的非线性性能和承载力

Non-Linear Behaviour and Load-Carrying Capacity of CFRP-Strengthened Lipped Channel Steel Columns

飞边槽桥部尺寸对模锻成形的影响

Influence of the bridge size of fash slot on die forming

卷边槽形截面受弯构件翼缘板的有效宽度

Effective width of the compressed flanges in lipped channels under bending

卷边槽钢梁受压翼缘畸变屈曲时的屈曲系数

On the distortional buckling coefficient of the compressed flange of lipped channel beams

冷弯薄壁卷边槽钢梁的弹性局部屈曲与畸变屈曲性能分析研究挠曲应变，弯曲应变

Elastic Local and Distortional Buckling Behavior of Cold-Formed Thin-Wall Lipped Channel Beams ; flexural strain

高强冷弯薄壁型钢卷边槽形截面轴压柱畸变屈曲试验研究

Experimental study on distortional buckling of high strength cold-formed steel lipped channel columns under axial compression

飞边槽结构形式对模锻成形的影响阶梯轴台肩圆角冷挤压成形速度场建模研究

Research on velocity field modelling of the multi-diameter shaft 's shoulder fillet forming by open-die cold extrusion

开式模锻中飞边槽的形式对锻件成形过程的影响较大。

In the open die forging , the type of flash has great influence on the process of forging .

制造门框，内加强筋，加强板，边槽，百叶窗和模件，可选用冷轧或者热轧钢板。

Fabricate frames , concealed stiffeners , reinforcement , edge channels , louvers and mouldings from either cold-rolled or hot-rolled steel .

应用计算机划分河道复式断面主边槽方法探讨

Probing into the method for using computer to divide a compound section of a river into main channel and the side

并根据分析结果对锻模进行了改进，在内壁增设飞边槽以利于锻造成形。

An improving project for the die design is proposed , that is adding a flash gutter at the inner wall of the piece to facilitate the forging deformation .

下端固接上端弹性支承变截面压杆的屈曲冷弯薄壁卷边槽钢构件受压畸变屈曲性能及加固控制措施分析

Buckling of round variable section compression bars with one side fixed and another place elastic supports Study on Distortional Buckling and Strengthening Measures of Cold-formed Thin-Walled Lipped Channel Columns

通过计算得到了适合各种弯起角度的斜卷边槽形截面特性计算公式，方便了手算求解构件的屈曲应力。

Section geometric properties of channels with different bending degrees of inclined simple edge stiffeners are gained by calculation . It is convenient for solving the buckling stress by hand .

本文根据能量原理，建立了边缘加劲板件的弹性屈曲理论和卷边槽形截面薄壁构件的板组相关屈曲理论。

According to the energy principle , the elastic buckling theory of edge stiffened plate elements and the elastic interaction buckling theory of cold formed lipped channel members are established in this paper .

在机柜的两边为使用者提供了走线的边槽，一般线路都是通过边槽固定的，可以使用专门的固定装置将网线、电源线分开布置。

In the Cabinets of both sides provides the user with alignment slot edge , the general lines are fixed through the side slot , you can use specialized fixtures to cable , power cord separate layout .

本文通过对这两种平面天线单元圆极化特性的讨论以及参数优化，对比仿真结果之后选择直边槽平面天线加工和测试。

Based on discussion and parameter optimization of these two kinds of realization of planar antenna unit circular polarization , and the comparison between the simulation results , the straight groove planar antenna is chosen for processing and testing .

本文应用不同尺寸的三点弯曲试样和带边侧槽试样，用实验方法研究了启裂J积分（J（1C））和JR阻力曲线的斜率（dJ/da）受试样尺寸的影响。

The effect of specimen size on the J_ ( Ic ) and the slope of J_R curve ( dJ / da ) was studied by using three point bending ( TPB ) and side-grooved TPB specimens of different sizes .

边切槽圆盘试样的岩石动态断裂韧度实验

Experiment on Dynamic Rock Facture Toughness Using Edge-notched Disc Specimen

提出用边切槽圆盘试样测量岩石动态断裂韧度的实验方法。

An experiment on dynamic rock fracture toughness test using edge-notched disc specimen is presented .

所述短边母槽，在其短边垂直面的上边沿设有短边防水沿；

The upper edge of the upright surface of the short edge female groove is provided with a short edge waterproof edge .

对大理岩实验的结果表明，边切槽圆盘试样能得到理想的劈裂加载；

The marble specimen experiment result indicates that : a perfect splitting load can be gotten from combination of SHPB and wedge ;

炉子后面有一冰箱边，洗碗槽下，还有橱柜里面都有老鼠！

There are mice next to the refrigerator , under the sink and inside the cupboard !

固定位于排气窗处的更换格删上部末端的槽并且将边插入到槽中。

Position the slot located in the upper end of replacement grille at the exhaust port and insert edge in the slot .

斜楔插板上的斜楔面推动废边的三角槽一侧，使板料向前运动，达到板料定位和自动送料的目的。

The surface of inclined wedge pushes the triangle side of the waste and makes the plate move ahead , thus meeting the requirement of position setting and feeding the plate automatically .

对比标准的矩形微带贴片天线，将微带贴片天线的辐射边设计为Koch分形状，同时开两个平行于辐射边的Koch分形槽。

Compared with normal rectangular microstrip patch antenna , the radiating edges of microstrip patch antenna are designed in the shape of Koch fractal , while two Koch fractal shape slots are cut in the antenna .