负载率

本文研究了行程50mm以内气缸的运动特性，分析了影响气缸高频动作的主要因素，包括气动缓冲、气缸行程、负载率及流量等。

In this paper , the movement performance of the cylinders whose stroke is from 1 mm to 100 ram is studied . , the factors to affect cylinder movement frequency are investigated , including of air cushion , cylinder stroke , load ratio and air flow rate etc.

基于负载率的异步机经济运行的研究

Research of Economical Running for Asynchronous Motor Based on Load Ratio

高负载率纳米PtRu／C催化剂的制备和表征

Preparation and Characterization of High Loading Nano PtRu / C Catalysts

ICP测试显示微波-氧化法具有快速、均匀且负载率高的优势。

ICP test showed microwave-oxidation method had advantage of speediness , uniformity and high supporting efficiency .

制备过程中的pH值为12时催化性能最佳，催化剂的煅烧温度为320℃，催化剂在载体上的负载率需高于50%。

The pH value during preparation was adjusted to be 12 and the appropriate calcinations temperature was 320 ℃ . The supporting ratio should be over 50 % .

基于OPA模型，构建考虑网络拓扑演化结构的改进模型，使用MATLAB仿真软件分析了平均负载率和电网拓扑特性对电力系统自组织临界性的影响。

Using the MATLAB simulation software , it has analyzed the influence of average load rate and network topology characteristics .

研究结果表明，该算法能够实现LIN总线带宽利用率的最优解，并能进一步降低LIN总线的总线负载率。

The results indicate that this algorithm can not only achieve the optimal bandwidth utilization of LIN bus , but also reduce the busload of LIN bus .

对变压器最佳负载率βopt进行了推导，给出了算例，并对基本电价进行了讨论。

The optimal load coefficient (β opt ) of transformer is derived . The example is presented . The basic price for electricity is discussed .

纳米粒子载药性能试验表明在0.05～1mg/mL范围内随着BSA浓度的增大，纳米粒子的载药量增加而负载率降低。

WSC NP loading studies showed that altering concentration of BSA from 0.05 to 1 mg / mL enhanced loading capacity of BSA but decreased loading efficiency simultaneously .

根据DEA的计算方法的评估结果，结合配电网的电压合格率、线路负载率、容载比等监测指标建立知识库，通过推理分析给出线路改善的建议措施。

The other module is knowledge base module , which is based on assessment result of DEA combined with monitoring information such as voltage qualification rate , line load , capacity-load ratio , etc. to get improving measure of distribution line through reasoning analysis .

结果表明，以二氯甲烷为分散溶剂、离子液体与沸石质量比为1.0：3.0、反应12h时离子液体在沸石上的负载率达到80%以上。负载型吸附材料对砷的吸附性能研究。

The result showed that ionic liquid loading rate was above 80 % when dichloromethane as the dispersion solvent , amount ratio of ionic liquid and zeolite is 1.0:3.0 , reaction time 12 h.Removal performance study of arsenic by ionic liquid-loaded adsorption material .

首先分析温度、水硅摩尔比、催化剂用量、时间对APTES水解缩合产物在群青颜料表面负载率的影响。

Firstly analysis the effect of temperature , molar ratio of water and silicon , catalyst concentration and time on the loading rate of hydrolysis and condensation product of APTES on the surface of ultramarine pigment .

模式Ⅰ对环境的压力小于模式Ⅱ，能值投资率（EIR），环境负载率（ELR）分别是模式Ⅱ的40.1%和18.3%；

The emergy investment ratio ( EIR ) and environmental loading ratio ( ELR ) of mode ⅰ were 40.1 % and 18.3 % of mode ⅱ, respectively , suggesting that mode ⅰ had less environmental pressure than mode ⅱ .

异步电动机负载率的在线测试及修正方法

On-line test and correcting method for loading ratio of asynchronous motor

配电变压器负载率与电压调整的关系

The Relation of Distribution of Transformers ' Load Rate and Voltage Spread

按变压器动态经济负载率选择变压器的经济容量

Selection of Transformer Economic Capacity According to Transformer 's Dynamic Economic Loading

箱式变电站箱内温升及变压器的负载率

On the Temperature inside Packaged Substations and the Load Factor of Transformers

用简易法测试交流电动机负载率的误差分析

Error Analysis by Simple Way to Test the AC Motor Loading Rate

三相异步电动机的最佳负载率选择

Selection of optimum load rate of three-phase asynchronous motor

其负载率最高为13.6%，最低为3.0%。

The best loading efficiency was 13.6 % and the lowest was 3.0 % .

基于负载率的配电网变电站与开闭所规划

The Planning of Substation and Switch Station for Distribution Network Based on Load Ratio

变压器最佳运行时效率和负载率的实验研究

Trial study of efficiency and load resistance of the transformer under the optimum running

变压器的负载率与节能

Load Rate of Transformer and Economization on Energy

提出了计算配电变压器经济负载率的数学模型和计算方法，并以此为依据，提出了配电变压器额定容量选择的新方法&年度费用最小法。

Presents the load rate mathematical model and its calculation method for the transformer .

按负载率分挡设计中小型电力变压器

Step Designing Distribution Transformers by Load Rate

变压器经济负载率确定方法的探讨

On Methodology of Determining Transformer Economic Loadings

三相异步电动机负载率的现场测试方法

The Test Procedure on Working Site for Measuring the Loading Percentage of Three Phase Induction Motor

封装结构使用动态头部的方式减少空间消耗，提高负载率，并通过均衡码率等方法充分利用光盘容量。

Package structure uses the dynamic head to minimize space consumption , improving the load factor .

为此，分析交流电动机负载率测试误差具有重要的意义。

Therefore , it is very important to analyze the AC motor loading rate testing error .

配电变压器负载率、效率与经济运行的探讨

Discourse on the Loaded Rated and Efficiency of Distribution Transformer and which of the Economic Operating