齿轮组

行星齿轮组也同样用于许多汽车变速器中。

Planetary gear systems are also used in many automatic transmissions .

该系统包括主动力行星传递齿轮组和转速对比齿轮传递机构。

The device includes the main planetary gear group and speed comparison framework .

动力通过一个行星齿轮组支持的连续可变传动系统（CVT）得到传输；该系统可实现油电模式间的无缝切换。

Power is sent through a planetary gearset-based continuously variable transmission ( CVT ) that provides seamless transitions between gas and electric modes .

当它们旋转式，也会带动侧方齿轮组的运转。

They drag the side gears along as they turn .

无声三速和四速传动齿轮组

Silent third and fourth gearset

降低高速传动齿轮组动载荷冲击的方法研究

Research of reducing the moving load impact in the meshing gear wheel group of the high-speed transmission

他想通过一个齿轮组的转动，来模拟需要周期函数，

In this , a system of meshing gear wheels would rotate to simulate the circular functions required .

他们要叠加30个周期函数，每一个都用一个齿轮组的转动来模拟。

There would in fact be thirty wave-like terms to be added , each simulated by the rotation of one gear wheel .

当侧方齿轮组旋转时，会将扭矩传递给驱动轴及相应的车轮上。

As the side gears rotate , they transfer torque to the drive axles , which in turn transfer it to the wheels .

如果没有变速齿轮组与副传动轴上的齿轮啮合，这时，就叫做空挡。

When none of the sliding gears is in mesh with its countershaft gear , the gears are said to be in neutral .

有级调速机构、无机调速机构分别与传动系统中的调速齿轮组和差动轮系匹配。

The step speed regulating mechanism and the stepless speed regulating mechanism are separately matched with the speed regulating gear set and the differential gear train of the transmission system .

其次，设计传动齿轮组连接偏振片和步进电机，通过对步进电机的细分控制提高偏振片的转动精度。

Secondly , an instrument for fixing polaroids and a gear team for driving between polaroids and step motor are designed . The rotation precision is enhanced with a step motor subdivided .

关键引擎部件的制造精密程度要达到仅有1微米（人类头发丝的平均直径为100微米左右），其中包括齿轮组、操控架和转向柱。

Key components of the engine are produced to an accuracy of just one micron ( the diameter of an average strand of human hair is about 100 microns ) and range from gear sets to steering rack and column .

采用齿轮油泵组，供油稳定、澡音低。

It adopts gear oil pump set , oil supply stable and has low noise .

高温高速大流量内啮合齿轮泵组的研制及测试

Development and Test of an Internal Gear Pump Group Used for High Temperature , High Speed and Large Flow

用杆轮分离法作高级齿轮连杆杆组的运动分析

Kinematic Analysis of High-ranking Geared Assur Groups by Spliting Link-gear Method

三轴滑移齿轮机构基本组优化设计

An Optimization Design of Computer Programming for Three-shaft Sliding Gears Mechanism Main Group

从这笔节省费用中，必须减去齿轮或者滑轮组的成本。

From this saving must be subtracted the cost of gears or belts and pulleys .

所述的传动链是：由传动轴通过一对同步带轮、一对圆锥齿轮以及一组轴线垂直布置的直齿轮带动定向齿。

The directional tooth is driven by the drive shaft by a pair of synchronous pulleys , a pair of bevel gears and a group of straight gears of which the axes are vertically arranged .

锥齿轮装配中的组装修配法

The Repairation in Assembling Bevel Gear

同时引入齿轮连杆基本杆组的概念，将一些颇有争议的齿轮连杆机构归为基本机构。

Simultaneity , by the concept of geared linkages groups , classifies some quite disputed geared linkages as basic mechanisms .

本文应用南开大学齿轮啮合理论研究组提出的齿轮啮合的数学理论，系统地研究了渐开线圆柱蜗杆传动的啮合原理。

In this paper , the author applied the mathematical theory of gear meshing , developed by Nankai University , to discuss systematically the meshing theory of Involute cylindrical worm gears .

该软件采用交互式窗口，操作简单，能迅速正确地确定齿轮三个公差组精度等级、齿厚极限偏差、各公差组的检验项目及其公差值。

This software used an interactive window , so the operation is simple , and can define rapidly correctly three gear tolerance classes , the tooth thick limit deviation , various tolerance class test item and the value of tolerance .

这四组小齿轮起到连接侧方齿轮组的桥梁作用。

These four pinions act as bridges between the side gears .

集成型的差速室、准双曲面齿轮的设计中，小齿轮组中心线在环形齿轮的中心线之上。

The integral type housing , hypoid gear design has the centerline of the pinion set above the centerline of the ring gear .

建立了符合Pro/E格式的齿轮参数表达式及参数驱动程序，对虚拟装配的齿轮组进行了干涉检验。

The parameter driver and expression for design were created in accordance with the style of Pro / E. The interference of gears assembled can be tested .

外壳内，设有小切换齿轮、分别与大链轮和大齿轮固连的端面齿轮轴、变速齿轮组和发电机组。

A small switching gear , a contrate gear shaft respectively fixedly connected with a big chain wheel and a big gear , a speed change gear set and a generator set are arranged in the casing .