齿轮模数

  • 网络gear module;gear modulus
齿轮模数齿轮模数
  1. 齿轮模数对激光熔覆层开裂倾向的影响

    Effect of gear module on cracking tendency of laser-clad coating

  2. 在此基础上,比较系统地研究了齿轮模数、原料成分等对变形丝的结构和性能的影响。

    On this basis , I systematically studied the effects such as module of gear and ingredients on structure and properties of profiled filament .

  3. 齿轮模数是齿轮几何尺寸计算的重要参数。

    Modulu is an important parameter for gear to calculate its geometrical dimension .

  4. 齿轮模数的现场测绘

    Mapping of Gears Modulus on the Scene

  5. GB/T12368-1990锥齿轮模数

    Modules of bevel gears

  6. 经过严密计算和实践反复验证,用公法线长度测绘法确定齿轮模数可满足要求。

    After iterative and rigorous practice , it turned out that it can meet the demand when using length of common normal to measure gears modulus .

  7. 利用m&z1线图确定渐开线直齿圆柱齿轮的模数和齿数

    A m-z_1 nomograph used for determining straight involute gear modulus and teeth

  8. 增大齿轮的模数、传动比和压力角等参数,以及提高转速、增大润滑油粘度可以提高齿面间的润滑油膜厚度。

    The calculation and analysis indicate that the oil film thickness become thicker with the increase of gear modulus , reduction ratio , pressure angle , rotating velocity and oil viscosity .

  9. 模数m≤12的齿轮用同模数圆弧滚刀加工;

    For the gear with the module m ≤ 12 , the arc gear cutter hob of same module is used for machining ;

  10. 齿轮传动系统齿轮模数的选择对噪声的影响

    On Influence of Gear Module upon Noise in Gear Transmission System

  11. 渐开线圆柱齿轮外啮合大模数

    " In volute cylindrical gear , external gearing , large modulus "

  12. 康明斯起动机单向器为棘轮式单向器,其驱动齿轮被设计成双模数制齿轮。

    The starter clutch of CAMMIS is ratchet type one , the driving gear of which is designed to double module one .

  13. 渐开线圆柱齿轮外啮合大模数齿轮指形铣刀样板是加工大模数齿轮的主要辅助工具。

    " In volute cylindrical gear , external gearing , large modulus " The finger milling-cutter templet of involute gear is the assistant tool mostly to machining big module gear .

  14. 但这些文献,多以在给定了传动方案等情况下,研究其最优的传动系统的设计参数如传动比、齿轮齿数和模数等的确定方法。

    But most of these references study the design parameters of optimization transmission scheme , at given transmission design , for example , the design method of transmission ratio , number of the gear wheel etc.

  15. 在分析范成加工外啮合非圆齿轮不根切的模数、偏心率取值范围的基础上,根据所建模型将加工外啮合非圆齿轮的范成过程用计算机进行了动态图形仿真。

    On the basis of selecting such assignment range of gear module and eccentricity that there would be no undercut for shaping the teeth of noncircular gears , dynamically graphic simulation of the shaping process was conducted on the computer by using the mathematical model developed .

  16. 本文详细介绍了用于齿轮仪器校准的齿轮样板模数、压力角、螺旋角等参数计算方法。

    The way of calculating the parameters of modulus , pressure angle and helix angle of the gear masters that are used to calibrate gear instruments is in detail in this paper .

  17. 计算得到了齿轮润滑的危险点以及齿轮模数、传动比和压力角对润滑油膜压力和膜厚的影响规律。

    The dangerous lubrication gear points are obtained and the effect of the gear module , transmission reduction , pressure angle on the lubrication film pressure distribution and film thickness profiles are also gained from the numerical calculation .

  18. 重点介绍了径节制齿轮的测绘和将径节制齿轮改造为模数制齿轮的方法。

    This paper gives the approach of mapping English system gear and how to transform English gear into modulus gear .

  19. 大模数齿轮在重大工程装备中的应用越来越多,而且齿轮模数也在不断增大,如海洋钻井平台上齿轮模数已达135mm。

    Large module gear is used more and more in great engineering projects , and the module of gear is continuously augmented , for example , the module of gear of the offshore drilling platform already achieves 135 mm .