预热

将烤箱预热到6挡。

Preheat the oven to gas Mark 6 .

PLC在特种水泥烧结窑预热装置中的应用

Application of PLC to Preheat Unit of the Cement Sintering Kiln

在预热过的烤箱里烤25分钟，或烤成金黄色。

Bake in the preheated oven for 25 minutes or until golden brown .

他等着汽车预热。

He waited for his car to warm up

把混合好的糊糊舀到饼干坯上，然后放入已预热的烤箱烘烤。

Spoon the mixture on to the biscuit base and cook in a preheated oven

我们沮丧地等了5分钟，让飞行员预热引擎。

We spent a frustrating five minutes while the pilot warmed up the engines .

机器空转了几分钟以使它预热。

The machine has been idling away for several minutes to get it warm .

首先你必须让发动机转起来预热。

In the first place you must rev it up to warm the engine .

预热诱导K（562）细胞热应激蛋白70高表达对高温引起细胞凋亡的影响

Effects of heat shock protein 70 overexpression on apoptosis of K_ ( 562 ) cell caused by hyperthermia

单向收费预热3G

One - way Charge : Another 3G Preparation

Ti在紫铜厚板不预热GTAW中防裂机理研究

Mechanism of Ti Avoiding Cracks of Copper Plate GTAW without Preheating

预热SHS制备SiC粉末的机理及工艺

SiC Powder Manufactured by Preheating SHS

预热温度提高到200℃时，薄膜呈杂乱取向，C轴取向不明显，这很不利于薄膜垂直磁各向异性。

When the temperature increases to 200 ° C , films appear to be with random orientation , c axis orientation is indefinite , which is bad for films PMA .

大厚度铝构件无预热状态下的脉冲MIG焊

Research on pulsed MIG welding for heavy thickness aluminum components without preheating

在不预热的情况下采用Ar+N2对厚壁紫铜进行了TIG焊接的研究，并在不同工艺参数下将试验值与计算值进行了比较。

The TIG welding of thick-wall pure copper adopting Ar + N_2 without preheating was studied .

Benchmark构造函数多次执行一个任务，首先确保完成代码预热，然后收集执行时间统计数据。

This Benchmark constructor executes a task many times , first to ensure code warmup , then to gather execution statistics .

另外，控制焊条熔敷金属扩散氢含量犤H犦、选择适当的预热温度和焊后及时进行消氢处理，也是防止冷裂纹和热影响区脆化必不可少的措施。

The absolutely necessary measures are to control linear energy and diffusible hydrogen content in electrode deposited metal , to select proper pre-heat temperature and to punctually perform hydrogen-eliminating treatment .

采用场发射阴极的X射线光源具有体积小，辐射强度高，频率响应快，可以随时开启，无需预热的优点。

Using field emission cathode , X ray source can be made with several advantages : smaller volume and brighter , high frequency response , in-time turning on , etc.

GMT片材制备过程中预热过程的研究

A Study of Preheating Process for CMT Manufacture

热传导预热装置及在SLS直接成形金属件过程中作用的研究

Study on the Preheating Device by Conducting Heat and its Effect in Directive Sintering Metallic Parts

研究了粉体预热温度、频率、环境温度等工艺参数及条件对PZT陶瓷电性能的影响。

The effects on electric properties of PZT ceramic were investigated , including preheating temperature , frequency , environment temperature and polarization .

为减少断头可采取以下措施：（1）降低出钢温度、预热金属模或推迟脱模时间以减小σR；

It is proposed that end-breaking could be decreased by ( 1 ) reducing casting temperature , preheating metal patterns or putting off the time of pattern drawing , Consequently lessening σ R ;

预热定形后，PTT织物的碱减量率比未热定形的织物明显降低；

After pre-setting at150 ℃, the alkali deweighting ratio of PTT fiber was clearly decreased compared with the fabric without heat-setting .

热接触组、预热处理组HP含量较对照组及热衰竭组明显升高（P<005）；

The contents of HP in heat exposure group , the preheat treating group increased significantly compared with the control group or the heat exhaustion group ( P < 0.05 );

在这些系列中第一次运行的结果被认为没有代表性，运行测试以使JVM和服务器“预热”。

The results of the first run in the series were not considered representative , run to get the JVM and the servers to " warm-up " .

结合SEM及EDS分析结果，燃烧合成Mg2Ni的结构形成过程可以描述为：（1）预热阶段的固&固反应；

The process of synthesis Mg_2Ni can be expressed as : ( 1 ) solid combustion in the preheat phase ;

通过石墨预热、搅拌等方法向Al-Ti合金熔液中加入石墨粉，使C进入Al合金并与Ti反应是可行的。

Preheated graphite powder was added to the molten Al Ti , after that the melt was stirred thoroughly , in order to allow C entering into Al alloy and reacting with Ti .

TiC-VC免预热耐磨堆焊焊条

Development of TiC-VC Hardfacing Electrode with Non-Preheating and Wear Resistance Properties

研究了预热温度对Al－Cr2O3燃烧体系绝热温度、燃烧速度以及最终铝基复合材料组织、性能的影响；

The effects of preheated temperature on adiabatic temperature , combustion velocity and the final microstructures and properties of Al based composite materials are studied .

提出将火焰结构划分为未燃区、预热区、反应区、产物区的方法进行研究，利用OH半峰宽度定义反应区边界及厚度。

The method which describe flame structure as four parts : unburnt zone , preheat zone , reaction zone , product zone is proposed , and use OH half width to define the boundary and thickness of the reaction zone .