预浸料

工厂设计与人类工程学碳纤维及预浸料工程设计探讨

Engineering design study of carbon fiber and prepreg plant

随着预浸料切割长度的增大、纤维含量的增加，材料的力学性能提高；

With the increment in the cut length of the prepreg and fiber content , the mechanical property increased .

用DMA研究环氧预浸料的等温固化过程

Dynamic mechanical analysis of isothermal curing of epoxy prepreg

该工艺采用预浸料铺层、热压罐固化工艺，通过对热缩材料的性能研究，发现可将其作为CFRP管成型的表面辅助均压材料。

Study showed that the thermal contractible material could be used to improve the surface quality of CFRP tube .

通过热失重TGA分析以及考察加工成型过程中工艺参数变化对复合材料介电性能、力学性能的影响，优化了预浸料热压成型工艺条件。

The prepreg hot pressing condition is optimized by analyzing TGA and studying influence of parameters on dielectric and mechanical properties of composites .

热熔法预浸料制备工艺研究用少量SIS对EVA热熔胶进行共混改性，再与石蜡、萜烯树脂混熔制成SIS改性热熔胶。

Study on the technology of hot-melt prepregs A modified hot-melt adhesive was prepared by blending of EVA and SIS and adding paraffin and terpene resin .

将模拟得到的固化结果与光栅FBG传感器监测试验结果进行对比后发现，不同铺层顺序和不同铺层厚度的预浸料在固化后的变化趋势与试验结果基本一致。

The simulation results obtained were compared with the test results monitored by FBG sensors , which showed that changing trend of cured prepreg with different stacking sequence and different layer thickness was consistent with test results .

湿气对EN体系的影响用DSC、TBA和重量分析法进行研究。提出了预浸料合适的操作温度、湿度和贮存条件。

The cured EN resin has excellent mechanical properties The effect of moisture on the EN system is investigated by DSC TBA and gravimetry And a suitable operating temperature , humidity and storage condition for the prepreg is suggested .

将FRP预浸料和钢片载体制成双层簧片试样，用振簧仪进行动态力学分析（DMA），从而监测、研究FRP的固化。

The curing process of FRP prepreg could be readily tested by means of the two-layered reed analysis method ( TRA ) , in which a strip of FRP prepreg was bonded to a thin steel and its DMA was tested with a vibrating reed instrument .

其次，研究了可控交联型聚芳醚酮树脂基复合材料的热塑成型、交联使用的方法。可控交联型聚芳醚酮（CCPAEK）具有良好的溶解性，可以采用溶液法制备预浸料。

Second , the thermoplastic forming and crosslinking treating processing of the Controllable Crosslinking Poly Aryl Ether Ketone ( CCPAEK ) matrix composites is studied .

本研究对玻璃纤维-铝合金层板（GLARE）的制备关键工艺参数进行了优化，包括铝合金薄板的底胶含量、预浸料的纤维体积含量、烘干条件和层板压制工艺。

In this study , Glass-aluminum laminates ( GLARE ) were prepared and the key factors of the preparation process , including content of primer on the aluminum sheets , fiber volume fraction of the prepreg , drying process and pressing process , were optimized .

本文详细介绍了由国产SW-280A／环氧树脂预浸料、SY-24C胶膜和Nomex纸蜂窝组成的中温材料体系蜂窝夹层结构的力学性能。

In this paper the mechanical properties of moderate temperature material system made by SW-280A / epoxy resin prepreg , SY-24C adhesive and Nomex honeycomb from the local supplier were studied .

通过摩擦磨损测试考察了纳米氧化铝／环氧树脂复合体系的耐磨性，关节轴承实际运行结果表明，纳米Al203的加入提高了环氧树脂基体预浸料的耐磨性，同时增加了轴承的运转寿命。

The results of the joint bearing actual running show that : the wear resistance of the prepreg based on epoxy resin were improved by adding nano-alumina , and the operating life of bearings were also increased .

本文简要介绍了钓鱼竿用大丝束（60K）碳纤维预浸料熔胶膜法浸渍工艺，并着重就影响预浸料质量的几个主要因素进行了讨论。

The hot-melt impregnation process of large tow carbon fiber ( 60K ) prepreg to prepare fishing rods is briefly introduced in this paper ; in addition , several typical factors which affect the quality of the prepreg are also discussed in detail here .

用常规预浸料制造复合材料模具技术探索

The investigation of composite mould manufacturing technique by using normal prepregs

复合材料预浸料自动铺带成型适宜性研究

Research on Molding Suitability of Prepreg Composites for Automated Tape Performance

中温固化碳纤维/环氧预浸料研究

Study on the carbon / epoxy prepreg cured at medium temperature

热熔预浸料用中温固化环氧树脂体系的制备

The preparation of MODERATE-TEMPERATURE curing epoxy resins used as hot-melt prepreg

连续玻璃纤维增强聚丙烯预浸料粉末法浸渍过程及界面控制

Powder impregnation process and interface control of continuous glass fiber reinforced polypropylene

大丝束碳纤维制备预浸料的关键工艺

Critical Process for Manufacturing Prepregs with Large Tow Carbon Fibers

大丝束碳纤维预浸料和快速固化预浸料。

Large tow carbon fiber prepreg ; Fast curing prepreg .

APC-2/AS4预浸料带热芯缠绕的显微特征

Microscopic Features of APC-2 / AS4 Tapes Wound with a Heated Mandrel

该预浸料已用于直升机次承力结构。

The prepreg had been used in helicopter secondary structure .

预浸料制备中的张力控制系统

Tension control system in equipment of preimpregnated material manufacture

热塑性复合材料用混纤预浸料特征

Characteristics of intermediate materials by FIBER-MIXING for thermoplastic composites

窄带预浸料制备工艺研究

Research on the manufacture process of narrow tape prepreg

适用于热熔法制备预浸料的氰酸酯树脂的制备

Preparation of Cyanate Ester Resin for Hot Melt Impregnation

环氧基复合材料预浸料铺覆工艺技术研究

Research on Placement Techniques of Epoxy Matrix Composite Prepreg

本文简介炭集团公司概况，重点介绍低温成型预浸料技术及其应用。

The low temperature moulding prepreg technology and it 's application are emphasized .

短纤维模压碳/碳刹车盘用预浸料的制备工艺及设备

Process and Equipment for Manufacturing Chopped Fibre Prepregs for C / C Brake Discs