集流器

圆弧型集流器改用为ISO文丘里喷嘴的分析与试验研究

Analyzing and Research of the Replacing Venturi Nozzle with the Inlet Quadrant Nozzle

石墨作集流器的初步理论探讨

Graphite carbon as the current collector : a preliminary theoretical study

集流器成形工艺飞机环控系统管道气流温度的测量

Measurement of Duct Airflow Temperature in Aircraft Environmental Control System

几种常见集流器的型线展开方法

Method of Profile Development of Several Collectors in Common Use

风机集流器弧段整体撑制成型

Integrative Manufacture Forming of Arc Segment for Fan Collector

大轴径分体轴通式碳刷集流器的设计与制造

Design and Manufacture of a Large Size Separated Collecting Ring with Carbon Brushes

贲门成形胃底再造在贲门癌手术中的应用集流器成形工艺

The application of cardioplasty and reconstruction of gastric fundus in the operation of cardiac carcinoma

介绍了风机集流器弧段压型、组焊的工艺方法。

The method of segmental arc pressing and combinational weld technology of fan collector is introduced .

集流器对前向多翼离心通风机气动性能的影响分析

Analysis of Bell Mouth to The Effect of Aerodynamic Performance for Forward Curved Multi-foil Centrifugal Fan

集流器在感应器上的应用接收系统和通用式机车信号共用感应器，不影响机车信号的正常工作。

Application of Electric Current Accumulator on Inductor There has no influence to the signal of locomotive .

轴流风机集流器阻力损失计算公式及最优结构参数的确定

The determination of formulae of resistance losses and the optimum parameters of structure of the collector in an axial fan

仪器配接了1个带有扶正器的集流器，在实现连续测量扶正的同时，进行半集流方式的流量测量。

One centralizer with the collector in the tool can make continuous measurements and semi-collecting liquid flow measurements in the same time .

以有效射程最大为目标函数建立数学模型，完成了整流器、集流器、喷筒等部件的优化设计。

The optimum design of parts , such as rectifier , collecting device and spray duct , were accomplished by the mathematical model based on the maximal range .

介绍了方案及制造工艺过程，经实际应用分析证明，应用此方法保证了集流器与叶轮安装配合的要求，且成本低，型线美观。

Through actual application analysis , this method is proved to meet the requirements of collector and impeller installation , and the cost is low , the profile is fine .

本文给出汽心泵压头特性、汽心变化、泵内水力损失、集流器内压力分布和径向力等主要特性的计算方法和程序框图。

The Calculation method and programs of pressure drop , vapor core variation hydraulic losses in vapor core pumps , prssure distribution and radial force in collecters are presented in this paper .

该系统主要由具有铁心绕组的转子和定子、附加调磁线圈、具有特殊磁极结构的杯形转子、感应式集流器和功率电子控制器等组成。

It consists of a rotor and a stator including iron winding , an additive magnetic field adjusting winding , a cup-type rotor with special magnetic pole , inductive slip-rings and power electronic controller .

在叶片振动试验台上，采用多点集流器测试系统，对三种松拉金连接方式、六种方案进行了系统的振动试验。

On the vibration test rig , where a multipoint slip-ring measuring system is used , systematic vibration tests are made for three types of loose lacing wire connections ( six alternatives in total ) .

当前旋转部件进行信号采集最常用方法是拉线式、水银式和电刷式集流器，它们都是基于有线连接的数据传输方式，在使用时存在弊端。

Currently the most commonly used method of the signal acquisition of rotating component is cable-type , mercury-type and brush-type bath collector ; they are based on wire-data transmission and the existence of defects in using .

实现了电压、电流及其相位的智能化跟踪补偿。集流器在感应器上的应用

The electromagnetic component acts as current inductor as well as voltage transformer , so the intelligent synchronized compensation among voltage , current and phase can be realized in the proposed method . Application of Electric Current Accumulator on Inductor

伞集流器存在非均衡及非线性的油气水三相流流体漏失，致使伞集流后测量通道内流型复杂多变，建立三相流涡轮流量计物理模型存在困难。

Due to the non-linear leakage and non equilibrium of oil-gas-water three phase flow with the petal type concentrating diverter , it makes the flow patterns in the measurement channel more complex variations and hard to establish the turbine flowmeter physical model of three phase flow .

仪器由全井眼持水率传感器、集流型涡轮流量计和集流扶正器构成。

This tool consists of a water holdup sensor , a collection flowmeter and a centralizer .