铺层设计

应用FWD评价旧混凝土路面及加铺层设计

Evaluating Concrete Surface by Use of FWD and Design of Layer

对AASHTO柔性路面加铺层设计方法的评述

Commenting on Design Procedures for Additional Layer of AASHTO Flexible Pavement

试验结果表明，经过环向、±45°和纵向混杂铺层设计的FRP管混凝土能有效地提高构件的承载力，构件具有很大的变形能力；

The experiment shows that concrete-filled FRP tubes can significantly improve the ultimate capability and deformed behavior of members by hybrid layer design in different orientation as transverse ,± 45 and longitudinal directions .

本文以现行《公路沥青路面设计规范》（JTJ014-97）中的沥青加铺层设计方法为依据，确立了以弯沉及拉应力为控制指标的极限状态方程。

According to the specifications for design of highway asphalt pavement ( JTJ 014-97 ), establishing two utmost state equations based on the deflection and positive stress .

根据沈大高速公路的路面检测数据，给出加铺层设计方法的厚度设计示例，并与我国现行规范设计方法及AASHTO设计方法进行对比分析，从而验证了该方法的合理性。

A design example is also given , based on test data of Shen-Da freeway , and a contrast analysis is made with the methods of this paper , current specification and AASHTO which verify the rationality of this method .

利用DASCM程序完成带整体油箱复合材料机翼铺层设计的优选方法、原理和算例。

This paper describes an optimum design method that is to use DASCM program for solving the structure design of the composite wings with inner integrated tanks and multiple external stores .

碳/环氧复合材料负膨胀结构性能铺层设计

Laminate design of the minus expansion of carbon / epoxy Composites

无纵向温度变形的复合材料管的铺层设计

Lay up Design for Composite Material Tube Having no Longitudinal Thermal Deformation

复合材料层合板及飞机进气道铺层设计与分析

Design and Analysis of Placement Layers for Composite Laminates and Aircraft Inlet

文中对碳/环氧复合材料负膨胀结构铺层设计进行了研究分析。

Laminate design of the expansion of Carbon / Epoxy composites is investigated .

厚壳玻璃钢艇体选材、铺层设计及工艺

Materials , Lay up Processing and Ply Design for GRP Hull of Boat

发电机复合材料护环的强度刚度分析和铺层设计

Stiffness and strength analysis and ply design of composite retaining rings for larg generators

碳纤维复合材料反射镜面板的铺层设计

Design of panel layers on reflector with CFRP

典型复合材料机翼铺层设计分析

A laminating design analysis for typical composite wing

旧水泥路面调查评价及加铺层设计实践

Evaluation of Existing Concrete Pavement and Overlap Design

对碳纤维天线成型模具、铺层设计、成型工艺等关键技术进行了讨论，提出了该制造技术中的一些先进方法；

Carbor-fibre antenna model , design , technology is discussed . Approach in manufacture is provided .

半刚性基层沥青路面的结构性加铺层设计主要以修复路面的结构缺陷为目的。

Structural overlays of semi-rigid asphalt pavement are used to remedy structural deficiencies of existing pavements .

碳纤维复合材料方形薄壁梁的铺层设计、制造工艺及试验

Layer lay & up design manufacturing techniques and test of graphite fiber composite square beam of thin wall

同时，对芳纶复合材料手糊轻型头盔的铺层设计进行了探讨。

The lay up design of light helmets prepared by aromatic polyamide fibre reinforced composite is also discussed .

混凝土路面的加铺层设计是目前混凝土路面大修或改建工作中的重要环节。

The design of overlay on concrete pavement is an essential link in concrete road repair or rebuild .

对碳纤维赛车车架进行了有限元分析，并优化了碳纤维铺层设计。

This paper analyzes the frame of carbon fiber racing bicycle with finite element method , and optimizes the carbon fiber pavement design .

一般情况下，补片采用和母板相同的铺层设计。

( c ) A reasonable choice is to let the lay-up design of the patch to be same as the mother plate .

为了具体说明本法的解题步骤以及如何选出铺层设计的优化方案举出了一个数例。

An example , illustrating the solution procedure and how to select the optimum scheme of lamination design , is presented in the paper .

涡流室式柴油机燃烧室的改进设计对燃烧过程的影响铺层设计对复合材料结构降噪特性的影响

THE EFFECT OF COMBUSTION SYSTEM IMPROVEMENT ON COMBUSTION PROCESS FOR A SWIRL CHAMBER DIESEL ENGINE On Improving Noise Reduction with Proper Design of Composite Material Structure

本文介绍了在受力复杂、结构和动力学要求苛刻、寿命及可靠性要求高的直升机旋翼桨叶上采用国产复合材料自行设计研制，从桨叶结构铺层设计、布置到产品试制与试验验证的主要过程；

Helicopter rotor blades are working in a complicated dynamic environment with critical requirement on struture dynamics life and high reliability , and composites are widely used in blade design abroad .

将选择的三种铺层设计方式按照同样的方式进行模拟，比较其结果得到一种较佳的铺层设计方法，经强度校核满足要求，初步完成复合螺旋桨的结构设计和铺层设计。

We get the optimal laminated method through comparing the result , and cater to strength check standard . Now , we accomplish to the design of structure and laminated method on propeller .

本文通过对1/2缩比模拟件的研制，探讨了碳纤维/环氧复合材料锥壳芯模设计、铺层设计、成型工艺等问题，并提出了相应的解决方法。

The problems in mandrel design , lay-out design and processing of Carbon / Epoxy composite cone were studied with the preparation of 1 / 2 scale-down simulant ; the corresponding solving method were raised .

本文系统研究了金属纤维/树脂基超混杂复合材料层压成型工艺（即SHCM）的铺层设计和铺层工艺，探讨并确定了固化工艺和后固化处理参数，从而使材料具有优异的性能。

In this paper the laminating process of metal fiber / resin matrix super-hybrid composite was systematically studied , including laminate lay-up and process . The best curing process parameters and heat treatment were discussed too .

对比分析国内外沥青加铺层设计方法，参照我国设计规范，探讨了适宜复合式路面加铺层的设计方法。

The domestic and foreign asphalt concrete overlay design methods are analyzed , and in term of our country 's design standard , the suitable design method of asphalt concrete overlay on the composite pavement is discussed .

然后根据复合材料所具有的铺层设计特点，通过引入中间设计变量和两级优化模型，构造出具有较强适应性的复合材料铺层顺序综合优化设计模型。

Then because of the character of laminate design in the composite , a conformable model of stacking-sequence synthesis optimization has been generated in this paper for composite through the intermediate design variables and two-level optimization model .