衬套

100P转向节衬套及平面轴承耐久性试验装置开发

Developing of Endurance Test Apperatus of 100P Steering Knuckle Bush and Plain Bearing

分析HXD1型机车牵引座的螺栓连接方式中的特殊点及其机理，并通过受力计算说明了衬套对螺栓使用可靠性的影响。

This paper analyses the special points and mechanism of bolt connection mode on type HXD1 locomotive traction base , and shows the effect of bush to bolt application reliability by stress calculation .

你将收到涂料、窗帘、家具垫衬套的样品。

You 'll receive samples of paint , curtains and upholstery

以ANSYS为平台，对衬套与轴承座的过盈联接进行了有限元计算。

The interference fits of bushing bearing has been calculated by finite element method based on ANSYS .

7′超重型圆锥MC尼龙衬套试用情况分析

The analyses of MC nylon liner used by 7 ' overweight circular cone

PTFE纤维织物衬套应用的研究

Research on Application of the PTFE Fabric Bush

除非CMM中有特殊的要求，衬套不得在原位大修。

Bushings should not remain installed during overhaul unless retained by specific CMM requirements .

Pinch阀橡胶衬套损坏原因分析

Cause analysis regarding rubber sleeve damage of pinch valves

衬套内爆ALE方法二维MHD数值模拟

ALE simulation of 2D MHD for liner

基于ADAMS软件，提出了悬架橡胶衬套各向刚度的优化设计方法及流程。

This paper studies the optimum design method and its process for determining the rubber bushing stiffness of suspensions on the basis of ADAMS software .

介绍了石墨渗铜材料作为固体火箭发动机（SRM）喉衬与长尾管衬套的烧蚀特性和机理。

The erosive property and principle of copper-infiltrated graphite as solid rocket motor ( SRM ) throat insert and tailpipe nozzle bushing are presented .

为了延长高炉风口衬套的使用寿命，采用SEM，XRD和实验手段，研究宝钢现用风口衬套的侵蚀机理。

In order to prolong working life of the lining sleeve for the blast furnace tuyere , the corrosion mechanism of lining sleeve was studied by the methods of SEM , XRD and oxidation at high temperature .

对于TC4合金，在改善疲劳品质上，带衬套冷胀孔强化比无衬套冷胀孔强化好得多。

Bushing cold expansion is more superior to cold expansion without bush on improving the fatigue property of TC-4 alloy .

改进后的密封结构，采用V形橡胶夹布盘根和聚四氟乙烯扶正板，盘根唇部与衬套的接触面积仅为原来的25～33%，减少了发热量。扶正板能自润滑。

As an improved feature , V cup packings of rubber with fabric and back-up rings of polytetrafluoroethylene are adopted , The total contact area between the sealing lips and the bushing is only 25 to 33 percent of the original packing-bushing contact area .

介绍了Pinch阀（管夹阀）的特点，分析了其橡胶衬套损坏的原因，并给出了调整该阀的具体步骤。

The features of Pinch valves ( pipe clamp valve ) have been presented , the causes leading to rubber sleeve damage being analysed , and concrete steps for adjusting valves of this kind being given .

本文应用多体力学方法研究了弹簧、阻尼器、缓冲块、橡胶衬套以及轮胎的非线性特性，并在ADAMS软件平台之上，研究了整车非线性多体动力学模型的建立。

In this paper , the nonlinear characteristic of the spring , damper , rubber bushing and tire has been studied by using multi-body system dynamics . Basing on ADAMS software , the establishment of the nonlinear full vehicle multi-body dynamics model has been studied .

介绍了FP-1电磁内爆实验中固体衬套内爆的一维单温磁流体力学计算。

One-dimensional simulations of single temperature magneto-hydrodynamics ( MHD ) are described for solid liner implosion experiments in the " FP-1 " equipment .

阐述了橡胶衬套对汽车平顺性、操纵稳定性及高频NVH特性的影响，并通过实例讨论了橡胶衬套对悬架运动学性能的作用和衬套刚度优化方法。

Influences of rubber bushes on vehicle ride performance , handling and stability and high frequency NVH properties are indicated , influences of rubber bushes on suspension kinematical characteristics and optimization method for bush stiffness is discussed with instances .

本文以XRL型铝衬套复合胶辊为例，运用静态和动态应力、应变理论，分析了运转过程中胶管、铝管承受加压后所产生之压缩应力及拉伸应力情况；

Taking the XRL aluminium bushing complex rubber roller as one example , the paper touches on the compressive stress and stretch stress of rubber and aluminium tubes running in pressure by application of static and dynamic stress and the strain theory .

对高精度偏心衬套更换方法的研究

The Study on the High-precision Deflect - quills for Replacing Methods

小议衬套壁厚公差与壁厚差

Discussion About Wall Thickness Tolerance and Wall Thickness Difference of Bushing

上部和下部衬套符合流畅平稳轻松操作阀门的标准要求。

Upper and lower bushings are standard for smooth valve operation .

专用的衬套也可用来嵌入无镶衬的渠道里。

Special liners are also available for inserting into unlined channels .

双金属衬套无镀烧结新工艺的开发与应用

Development and Application of Bimetal Bush Sinter Technology without Copper Plating

这钢丝弹簧绕得很均匀。前钢板弹簧卷耳孔衬套

The wire spring is evenly coiled . front spring eye bushing

通过扩大的开口取出旧的螺纹衬套。

Take out the old threaded bush through the widened opening .

煤矿罐笼衬套应用铁基石墨复合材料研究

Research on colliery cage lining applying iron matrix , graphite composite

起动机的耐久性试验汽车起动机衬套的使用

Endurance Test of the Starting Motor Using of Vehicular Starter Bushing

低温绝热泡沫塑料双金属连杆衬套的应用

The foamed plastics used in cryogenic insulation bi-metal bushes for cor-rods

请小心敲动，不要损坏塑料衬套！

Be careful not to break the plastic bushing when tapping !