地址寄存器

dì zhǐ jì cún qì
  • address register
地址寄存器地址寄存器
  1. dar(数据地址寄存器)包含处理器尝试访问的地址,这一行为将引发页面错误。

    The dar ( Data Address Register ) contains the address that the processor tried to access , which then caused a page fault .

  2. 在调试信号时,需要查看的一些重要寄存器包括GPR、指令指针(NIP)、机器状态寄存器(MSR)、Trap、数据地址寄存器(DAR)等等。

    Important registers to look for when debugging through signals are the GPRs , instruction pointer ( NIP ), machine state register ( MSR ), trap , data address register ( DAR ), and so on .

  3. 在边界扫描链设计中,采用了自定义的控制、数据、地址寄存器与指令寄存器相结合的访问ROM和RAM等相应空间方法,与原有的地址译码电路相结合,减少了硬件的开销;

    The boundary scan adopts the address , data , control register together with instruction register to access relevant space , utilizes original circuit of core of DSP , decreases the cost of hardware ;

  4. 一种基于反馈信息的地址寄存器提升方法

    An Address Register Promotion Method Based on Feedbacks

  5. 局部存储器的地址寄存器

    Local storge address register addressable memory

  6. iar-指令地址寄存器。

    Iar-The instruction address register .

  7. 处理机本机存储器地址寄存器

    Processor local storage address register

  8. 打印行缓冲地址寄存器

    Print line buffer address register

  9. 维护控制地址寄存器

    Maintenance control address register

  10. 控制器总线地址寄存器

    Controller bus address register

  11. 存储器缓冲地址寄存器

    Memory buffer address register

  12. 实验存储器地址寄存器

    Experimental memory address register

  13. 磁道现行地址寄存器

    Track current address register

  14. 逻辑磁道地址寄存器

    Logic track address register

  15. 当传输信令帧时通过I/O域重映射技术,由用户程序直接对网络设备的基地址寄存器进行读写,减少了频繁陷入内核带来的开销。

    Thirdly , when token packet transmitted , " Remapping Specific I / O Regions " technique is used to allow user accessing device 's base address register directly and avoid the unnecessary expense that would be caught in frequently access kernel .

  16. 其次,给出了基于PCI9052的板卡的配置方法,包括地址范围寄存器、基址寄存器、与片选控制寄存器的配置。

    Secondly , the collocation method of the board was introduced , thus the configuration of address rage register , base register and chip selection control register was involved .

  17. 你也可以设置断点并检查特定内存地址或寄存器的内容。

    You can also set breakpoints and examine the contents of specific memory locations and registers .

  18. 存储器地址选择寄存器

    Memory address select register

  19. 第一个指令负责加载,第二个指令旋转此值以便所请求的地址位于寄存器的开始。

    The first instruction does the load and the second instruction rotates the value so that the requested address is at the beginning of the register .

  20. 它把导致页面失效的虚拟地址装入寄存器中,再利用中断句柄来通知操作系统。

    The processor will store the virtual address which caused the page fault in a register , and then signal the operating system through an interrupt handler .

  21. 除错监视程式提供一个简单的命令集来显示和记忆体地址和寄存器、建立和移除断点,并且运行你的程式。

    The debug monitor provides a set of primitive commands to view and modify memory locations and registers , create and remove breakpoints , and execute your program .

  22. 从规划PLC的控制命令、I/O地址、内部寄存器资源开始展开论述,并结合软件结构,说明了PLC的编辑和存储结构、循环扫描执行等模块。

    The PLC Command , I / O address , internal relay resource , the structure of the software , edits modules , memory frame and execution cycle are described in detail .

  23. 下面的输出显示了kprobe的地址以及eflags寄存器的内容

    The following output shows kprobe 's address , and the contents of the eflags registers

  24. 这将总会是它为了将指定地址移到寄存器的开始所需向左移位的字节数。

    This will always be the number of bytes it needs to shift left to move the address specified to the beginning of the register .

  25. 一个逻辑地址包含了段寄存器的说明符及偏移量

    A logical address consists of a segment register specifier and offset .

  26. 物理地址大小可以与寄存器带宽一样大,也可以比它大或小。

    The physical address size can be the same as the register width but could be larger or smaller .

  27. 地址路径选择指示符存储器地址选择寄存器

    Address routing indicator memory address select register

  28. 地址总线被处理器用来选择在特定外设中的存储器地址或寄存器。

    The address bus is used by the processor to select aspecific memory location or register within a particular peripheral .