卡箍

kǎ ɡū
  • Clamp;collar
卡箍卡箍
  1. CDL测井仪打捞工具结构简单,主要由锥度套、压盖短节和卡箍组成,工具下螺纹与铣筒连接,上与打捞钻具连接。

    The CDL tool is simple in structure , consisting of tapered housing , gland sub , and clamp collar . The lower threads of the tool connect with the milling tool , while the upper threads connect with fishing tool .

  2. 卡箍:一个金属环,可确保杠铃固定在一定重量上。

    Collar : A metal component that encircles the bar and secures the weights in place .

  3. 超临界萃取釜卡箍式快开结构的CAD软件开发

    The development of CAD software for quick closure device of supercritical extraction kettle

  4. 利用裸管对CTX线管修复技术的研究卡箍式管线长坡地段地面裸管铺设受力分析

    A Study of Skill of Renovating CT X-Ray Tube Using Naked Tube Stress Analysis of Naked Victualic Coupling Pipeline in Long-sloping Area Lay Out

  5. KRH型卡箍式柔性管接头是传统的法兰盘的替代产品。

    KRH flexible coupling of housing is a product of replacing flange plate .

  6. 运用有限元(ANSYS)软件对5L萃取釜卡箍快开密封结构进行强度和接触行为的分析,分析可知结构安全可靠,密封性能良好。

    The structure intensity and contact behavior of quick-opening clamping band seal structure for the 5L extraction kettle is analyzed by finite-element ( ANSYS ) software . It is verified that the structure is safe and the seal performance is good .

  7. 使用结构分析程序(SAP5)对卡箍式管道接管进行有限元分析,求出接管的危险断面。

    Using the structural analysis program , the finite element analysis for hoop flex coupling has been made , and the dangerous section of coupling has also been sought out .

  8. 打开螺钉式卡箍并取出燃油滤清器。

    Open the screw-type clamp and take out the fuel filter .

  9. 拔出冷却液连接软管上的软管卡箍。

    Pull off the hose clamp on the coolant connecting hose .

  10. 将冷却液管推入发电机并安装弹簧卡箍。

    Push coolant line onto generator and fit the spring-band clamp .

  11. 为此,应松开通风管并松开卡箍。

    To do this , unclip vent line and loosen clamp .

  12. 卡箍式离心铸铁排水管渗漏原因分析与对策

    Leakage Analysis and Countermeasures of Centrifugal Cast Iron Drainage Pipe Clamp

  13. 卡箍零件成形工艺分析及整形模具设计改进

    Forming Process Analysis and Improve of Sizing Die for the Hoop

  14. 使用张紧卡箍将侧梁固定至车身。

    Fix the side member to the body using tensioning clamps .

  15. 打开紧固卡箍并旋开进气消音器。

    Open the fastening clamp and unscrew the intake muffler .

  16. 卡箍式管线长坡地段地面裸管铺设受力分析

    Stress Analysis of Naked Victualic Coupling Pipeline in Long-sloping Area Lay Out

  17. 松开两个热膜式空气质量流量传感器上的螺钉式卡箍。

    Release screw-type clamps on the two hot-film mass air flow sensors .

  18. 首先插入弹簧卡箍,然后插入管接头。

    First insert the spring clamps , then the couplings .

  19. 镀锌钢管卡箍连接技术的应用

    Application of the hoop - join of zinc-plated steel pipes

  20. 热采蒸气输送管线卡箍紧固螺栓失效分析计算

    Strength Calculation for Coupling Bolt of Pipe in Thermal Recovery

  21. 向上稍微按压进气消音器并拆离紧固卡箍。

    Press the intake muffler upwards slightly and detach the fastening clamp .

  22. 松开卡箍并将进气软管从节气门壳中拔出。

    Loosen clamp and pull intake hose off throttle housing .

  23. 确保弹簧卡箍没有过度拉伸。

    Make sure that the spring clamps are not overstretched .

  24. 为此,剪开单向卡箍。

    To do this , snip open the one-way clamp .

  25. 将螺钉式卡箍推到偏置位置上。

    Push on the screw-type clamps in an offset position .

  26. 轻型高温快卸卡箍的研制

    Development of Light High - Temperature Quick - Release Clamp

  27. 放上防侧倾杆,并用四颗紧固螺钉固定卡箍。

    Position anti-roll bar and fit clamps with the four fastening screws .

  28. 为此,请拧紧卡子和卡箍。

    To do this , tighten the clips and clamps .

  29. 用张紧卡箍将减震器支座安装到车身。

    Fix the spring strut mount to the body with tensioning clamps .

  30. 检查车底的卡箍,如有必要,予以更换。

    Check clamps on the vehicle underbody , and replace if necessary .