化学镀镍
- 网络electroless nickel plating;Ni-P;ENP
-
铝和铝合金化学镀镍工艺
Technology of Electroless Nickel Plating on Aluminium and Aluminium Alloys
-
为降低化学镀镍的成本,采用工业级药品配制镀液。
On the Grade " ji " In order to reduce the cost of electroless nickel plating , industrial chemicals were adopted .
-
用C语言编程实现化学镀镍工艺优化和模拟
Stimulation and Implementation of Technological Parameter Optimization for Chemical Nickel Plating by C language
-
超塑性Zn-Al合金化学镀镍工艺
Electroless Ni Plating of Superplastic Zn-Al Alloy
-
结果表明,镁合金化学镀镍层的P含量为6.68%(质量分数),与基体结合良好。
The results showed that phosphorus content of electroless coating was 6.68 % wt , and the films ' adhesion resistance was good .
-
钢铁表面纳米Al2O3复合化学镀镍的研究
Composite Electroless Nickel-nano Al_2O_3 Coatings on Steel Substrate
-
化学镀镍-高磷合金晶化行为的现场XRD研究
In situ XRD Investigation on the Crystallization Behaviors of Electroless High-Phosphorous Ni-P Alloys
-
ABS塑料表面化学镀镍无钯活化工艺研究
Investigation of Palladium-Free Activation Process for Electroless Nickel Plating of ABS Plastic
-
ABS塑料低温化学镀镍新工艺
New Technology of Chemical Nickel Plating on ABS Plastic at Lower Temperature
-
借助SEM、X射线能谱仪对化学镀镍织物表面结构进行了表征和分析。
By means of SEM and EDS , the surface structures of modified PET fabric were investigated .
-
以此为目标,本文开展纳米Al2O3复合化学镀镍的研究。
In these preconditions , experiments were carried out to study the nano-Al_2O_3 electroless composite plating .
-
新型ABS化学镀镍工艺的初步研究
Tentative Study of Novel Electroless Nickel Plating on ABS
-
SiCp/Al复合材料表面无钯活化化学镀镍的研究
Study of electroless Ni plating with palladium-free activation on the surface of SiC_p / Al composites
-
桦木单板化学镀镍过程的FTIR和XPS分析
FTIR and XPS Analysis of the Process of Electroless Nickel Plating Birch Veneer
-
利用SEM观察了活化膜和预化学镀镍层的表面形貌。
The morphology of activation film and pre-electroless Ni coating was analyzed by scanning electron microscope ( SEM ) .
-
稀土元素La、Nd和Eu对化学镀镍层结构与性能的影响
The Effect of La , Nd and Eu Rare Earth on the Structure and Performance of Ni-P Coating
-
化学镀镍溶液渗透对多孔PTC陶瓷影响的机理研究
Influence of Permeation of Electroless Nickel Plating Solution on Porous PTC Ceramics
-
钢纤维及化学镀镍增强Al2O3-SiO2基陶瓷的研究
Research on a1_2o_3-sio_2 based ceramics strengthened by steel fibre and electroless nickel coating
-
研究了化学镀镍-铜-磷镀液的组成、pH、温度等工艺参数对化学镀镍-铜-磷镀层镀速和组织性能的影响。
The influence of Ni-Cu-P electroless plating bath composition , pH , temperature on the Ni-Cu-P alloy deposition rate , structure and properties was studied .
-
化学镀镍磷合金表面涂覆SiO2溶胶-凝胶封孔技术研究
Research on Pore Sealing of Electroless Ni-P Plating Alloy Covered with SiO_2 Sol-Gel
-
研究采用以硼氢化钠为还原剂的化学镀镍溶液,在电子陶瓷基体上镀覆了Ni-B合金镀层。
A Ni B alloy coating bas been plated on electronic ceramic body in chemical nickel plating solution by use of natrium borohydride as a reducer .
-
PZT陶瓷酸蚀工艺对化学镀镍附着力的影响
Effect of PZT Ceramic ′ s Acid Corrosion Technology on Adhesion of Electroless Plating Nickel
-
六方BN微颗粒表面化学镀镍的动力学
Kinetics of Chemically Plating Nickel on the Surface of Hexagonal Boron Nitride Micro-particles
-
研究了杨木单板表面化学镀镍过程中pH值和温度变化对镀层的电磁屏蔽性能和表面导电性能影响。
The effect of pH and temperature on electromagnetic shielding and surface conductance of nickel-plate was studied in the course of processing electroless nickel-plated poplar veneers .
-
研究了用于化学镀镍液中的三种不同缓冲体系的pH值随加入酸量的变化情况,得出了相应的缓冲容量曲线。
A chart of buffer capacity is drawn by measuring the pH values of three different buffer systems , which vary with the volume of added acid .
-
讨论了ABS化学镀镍前处理工艺条件的选择、温度及pH对化学镀镍的影响。
The selection of pretreatment process conditions of electroless nickel plating on ABS and the influence of pH on electroless nickel plating was discussed .
-
多钼酸盐与由Mg(OH)2组成的腐蚀产物一起构成较为致密的表面膜,同时为后续的化学镀镍提供较为平整的表面。
A compact film composed of the corrosion products of multi-molybdate and Mg ( OH ) 2 can provide a relative even surface for the subsequent chemical coating .
-
研究了常温下敏化活化一步进行的ABS塑料化学镀镍工艺。
Electroless nickel plating on ABS plastic was studied . In this process , sensitization and activation were completed at one step .
-
研究了SiC纤维正交电路屏/环氧树脂复合材料和化学镀镍SiC纤维正交电路屏/环氧树脂复合材料的吸波性能。
Radar absorption performances of orthogonal-arranged SiC_ ( f ) circuit / epoxy composite and orthogonal-arranged electroless-nikel-plated SiC_ ( f ) circuit / epoxy composite were studied .
-
实验结果表明,在聚氨酯泡沫塑料基体上进行化学镀镍,它的最佳工艺参数是pH值为8.0左右,温度控制在45℃左右。
The experimental results show that the optimization parameters of nickel electroless plating on polyurethane plastic foam are that pH value is about 8.0 , and the temperature is about 45 ℃ .