切削部分
- 网络cutting part
-
针对该骨钻系统主要做了以下几方面工作:一、机械结构设计。包括运动执行部分、动力驱动部分、刀具切削部分、排屑冷却部分、定位操作台。
The major work to the system is as follows : First , the mechanical structure design , including execution part , driving part , knives cutting part , scraps discharge and cooling section , and positioning work station .
-
基于Matlab的可转位车刀切削部分优化
An Optimal Modeling of Turning Cutting Tools with Indexable Inserts Based on Matlab
-
可转位浅孔钻切削部分几何建模
Dynamic Geometry Model for Cutting Section of Drills with Indexable Inserts
-
建立刀具切削部分几何形状设计理论的新思路
New method for establishing the theory of metal cutting tool geometry design
-
试谈刀具切削部分几何角度实验教学方法的改革
Several Geometric Angles of the Blades of Cutting Tools An Experimental Teaching Method under Reformation Process
-
加工系统由三大部分构成,即机床、刀具联接系统和刀具切削部分。
The main components of machining system are the machine tool , the toolholder / spindle interface and the cutting tool .
-
刀具参与切削部分主要集中在刃口区域,刃口区的物理性能、机械强度、几何参数对切屑的形成以及切削过程力-热特性将起到至关重要的作用。
Tool edge area is the main locations involving cutting process . The physical properties , mechanical strength , and geometric parameters play a crucial role in chip formation and characteristic of cutting force and temperature .
-
保护切削工具显露部分,免受腐蚀。
Protects exposed machina tools parts from corrosion .
-
超硬磨料层是起切削作用的部分,由超硬磨料和结合剂组成。
Super-hard abrasive layer is part of the role played cutting by the composition of super-hard abrasive and binding agent .
-
最后,对机床主轴的力变形误差模型进行了修正,使其能准确计算切削力静态部分引起的主轴误差。
In the end , the spindle model is corrected by EMD method , so that the deformation caused by static force can be calculated correctly .
-
在进行数学分析时,将该种过渡切削分为两部分,纵横向切削和横纵向切削。
In mathematical analysis , the transitional cut of wood was divided into two parts ;
-
如果大修时要局部切削腐蚀或损伤部分,必须使翻修凹陷表面与原表面缓和过渡。
When locally machining out corrosion or damage during overhaul , a gradual transition into the reworked depression is necessary .
-
将钻头前端未切削的工件材料部分定义为叠合层,指出叠合层的刚度分布情况是决定各个层间分层形状的关键因素。
Uncut layers in front of drill is called remaining layer , and its distribution of stiffness is the key factor to determine the delamination shapes of the interplies .
-
试验分为斜角纵向切削和斜角横向切削两部分,采用两种试材和两种切屑厚度。
The experiments are made up of longitudinal oblique cutting and transverse oblique cutting . Each type of experiments include two species of wood and two kinds of chip thickness .
-
由于单位切削力尺寸效应的影响,微切削中残留部分毛刺的高度增大。
The exit burr height will increase due to the effect of size effect of specific cutting force .
-
每个切削端都具有在其末端的切削头,主体部分,主体部分中的凹口以及定位于凹口中的套圈。
The cutting ends each have a cutting tip at a distal end , a body portion , a recess in the body portion and a retainer positioned in the recess .