侧梁

cè liáng
  • side beam;side sill;side frame;curb girder
侧梁侧梁
侧梁[cè liáng]
  1. 通过高级配合技术完成构架侧梁、横梁及构架总装。

    Through advanced assembly technology to assemble the side beam 、 beams and bogie frame .

  2. 为进一步控制侧梁的焊接残余变形,本文研究了焊接方向,顺序,反变形等综合措施作用下的侧梁焊接变形规律。

    For controlling the welding residual deformation of the side beam , the welding deformation law by the combined effect with the welding sequence and direction and the reverse-deformation is researched .

  3. X(6B)型集装箱专用平车侧梁制造工艺

    Manufacturing technology of side sills for X_ ( 6B ) container flat cars

  4. 和谐HXD1型机车构架侧梁立板焊缝X射线探伤工艺的研究

    Research on X-ray flaw detection technology for butt welds on side beam of bogie frame for type HX_D1 locomotive

  5. 只能使用《车间设备手册》中认可的焊机对侧梁执行mig焊接。

    Only apply MIG welds on the side member using the welders approved in the workshop equipment manual .

  6. 对SS系列电力机车车体侧梁牵引座进行了比较及强度计算,分析了侧梁牵引座的结构特性,提出了不同的优化结构方案;

    This paper compares and calculates strength of the side-beam traction holders of SS series electric locomotive car body , analyses the structure characteristic of them .

  7. DJ1构架侧梁焊接变形的控制

    The Controlling of welding distortion for DJ 1 bogie side frame

  8. 由于侧梁非严格对称,且外部4条主焊缝环绕在纵向中性轴(X轴)的四个角点;焊缝金属收缩是形成焊接残余变形的主要因素。

    Because the side beam is asymmetric , and the external four longitudinal weld locate four corner of longitudinal neutral axis ( X axis ) of the side beam . For the groove weldment , the shrinkage of weld metal is the main factor making residual welding deformation .

  9. 介绍了DJ1构架侧梁的结构,分析了其焊接变形特点,阐述了控制构架侧梁焊接变形的工艺措施。

    This paper mainly describes the structure of DJ 1 bogie side frame and analyzes its distortion characteristic . The controlling technology of welding distortion has also been presented .

  10. 在区域和中对外侧梁进行电阻电焊。

    Resistance spot-weld the outer side member in the areas and .

  11. 拆下后轴托架侧梁上的制动软管支架。

    Remove brake hose bracket on the rear-axle carrier side section .

  12. 拧紧后轴托架侧梁和横梁上的螺钉。

    Tighten screws on rear-axle carrier side section and cross member .

  13. 用角度研磨机切断侧梁区域。

    Cut through the side member area using an angle grinder .

  14. 安装后轴托架侧梁处的两个控制臂。

    Fit both control arms at the rear-axle carrier side section .

  15. 将侧梁焊接在下侧梁区域中。

    Weld in side member in area of lower side member .

  16. 使用张紧卡箍将侧梁固定至车身。

    Fix the side member to the body using tensioning clamps .

  17. 高速动力车构架侧梁焊接结构优化研究

    Optimization of welded structure in bogie frame of high-speed locomotive

  18. 用气体保护塞焊,将侧梁焊接到区域。

    Plug-weld the side member in area under shielding gas .

  19. 气体保护焊接内侧梁和侧梁。

    Weld inner side member and the side member under shielding gas .

  20. 使用惰性气体在区域中对外侧梁进行塞焊。

    Plug weld the outer side member in area using inert gas .

  21. 防石撞击梁为侧梁提供了有效的保护并使外观更具吸引力。

    Rock rails offer effective protection for the side members and look attractive .

  22. 将防侧倾杆安装到后轴托架侧梁上。

    Fit anti-roll bar on rear-axle carrier side section .

  23. 高速机车构架侧梁的焊接顺序

    Study of different welding sequences in the bogie frame of the high-speed locomotive

  24. 更换轮罩上部侧梁。

    Replace side member for wheel housing upper section .

  25. 将侧梁固定到车架头部并固定侧梁的支架。

    Fix side member to frame head and secure support for side member .

  26. 更换保持架并连接到侧梁上。

    Replace holder and attach to side member .

  27. 机车侧梁牵引座结构优化设计

    Optimization design for side-beam traction holder of locomotive

  28. 将内部侧梁固定到车身。

    Fix inner side member to the body .

  29. 盖瓦叠板式盖瓦式叠板轿车侧梁内板顶盖冲压成形数值模拟研究

    Research on Stamping Forming Numerical Simulation for Side Beam Internal Plate Cover of Car

  30. 将轮罩上部的侧梁固定到车身。

    Fix the side member for the wheel housing upper section to the body .