主动齿轮

机车电机主动齿轮轴轴承布置分析

Analysis on Bearing Arrangement of Driving Gear Shaft of Locomotive Motor

研究了现有的3种机车电机主动齿轮轴轴承布置方式。

It is studied the existing three kinds of bearing arrangement for the driving gear shaft of locomotive motor .

SDD8型机车用牵引主动齿轮的设计

Design of driving gear for SDD_8 diesel locomotive

EQ-153汽车后桥圆锥主动齿轮裂纹分析

Analysis of Cracks in Bevel Drive Gear of EQ-153 Rear Axle

珠海发电厂700MW进口机组在调试期间汽轮发电机盘车装置轮齿损坏的原因主要是盘车第二级减速主动齿轮设计强度裕度不足。

Damages to turbine turning gear in commissioning of Unit 1 in Zhuhai Power Station are presented . The main cause for the damage lies in lack of strength in teeth design .

LZ110型汽车主传动器主动齿轮轴隔套改进设计时，采用了塑性套，并做了一些试验和计算。

A distance sleeve in the main drive gear of LZ110 minicar has been improved by using a plastic sleeve instead of a rigid one , and it has been supported by test and calculation .

机车电动机悬挂装置主动齿轮断裂分析

Failure analysis of driving gear in motor suspension device of locomotive

传动轴主动齿轮凸缘主动齿轮轴承抛油环

Propeller shaft pinion flange main drive gear bearing oil slinger

有环形内齿轮的飞轮主动齿轮轴承抛油环

Flywheel with ring gear main drive gear bearing oil slinger

双主动齿轮单出轴齿轮

Twin-input single-output gear bevel pinion and bevel gear set

传动轴主动齿轮凸缘

Drive pinion cone bearing propeller shaft pinion flange

注意到主动齿轮的齿数比冠状齿轮少。

Note that the input pinion is a smaller gear than the ring gear .

油泵主动齿轮及主动轴断裂分析

Fracture Analysis of Drive Gear and Pump Axle

从差速箱处拆卸主动齿轮。

Remove pinion gears from differential case .

当不准许主动齿轮旋转时，向上推环齿轮，并放牢它。

Push and hold ring gear upward while not allowing the pinion gear to rotate .

汽车双联主动齿轮的冷锻成型工艺

Cold Forging Process for Automotive Gear Cluster

双主动齿轮单出轴齿轮双轴涡轮喷气发动机

Twin-input single-output gear double-compound turbo jet

主动齿轮轴承抛油环主动小齿轮锥形轴承差速器主小齿轮轴承罩

Main drive gear bearing oil slinger

重型车后桥主动齿轮喷丸强化工艺及设备

Technology and Equipment of Peen Shot Strengthen for Drive Gear of Rear Axle in Heavy Duty Vehicle

拆卸主动齿轮止推垫圈

Remove Pinion Gear Thrust Washer

计算结果表明：主动齿轮轴两端支撑结构对轴承受力和齿轮啮合最有利。

The result indicates that the two-terminal bracing structure is optimum for bearing load and gear mesh .

把差速箱推进轴壳的主动齿轮侧清洁驱动桥轮轴底盘和壳内油路。

FORCE DIFFERENTIAL CASE TO RING GEAR SIDE Clean axle shaft tubes and oil channels in housing .

以两段高阶椭圆组成的连续光滑封闭的曲线作为主动齿轮的节曲线，依据齿轮啮合理论建立了其配偶从动齿轮节曲线设计及该齿轮机构传动比函数的数学模型。

The curve of higher order pitch-line design for driven gear and velocity ratio function is modeled mathematically .

齿轮传动的浇包起重机起重机油泵主动齿轮

Hoist pump drive gear

齿轮齿条传动压力机锯齿形内齿主动齿轮冷挤压成型技术研究

Rack and pinion press Study on Cold Extruding Forming Technology for the Driving Gear of Saw-tooth Inner Gear

通过合理分配变形程度、控制金属流动，设计出精密成形工艺的合理中间预制坯，并采用温锻制坯与冷挤压相结合的复合成形工艺，成功地进行了启动主动齿轮精锻件的生产。

Proper preforging blank form has been designed through reasonable distribution of deformation extent and control of metal flow .

基于动力吸振器的潜艇推进轴系轴向减振研究把差速箱推进轴壳的主动齿轮侧

Design of dynamic vibration absorbers to reduce axial vibration of propelling shafts of submarines FORCE DIFFERENTIAL CASE TO RING GEAR SIDE

介绍了汽车变速箱中的一个关键零部件&双联主动齿轮的冷态镦粗、挤压及冲孔的复合成型工艺。

This paper introduces cold heading and combined forming process of extrusion and punching for gear cluster , a key part of automotive gearbox .

主动齿轮和从动齿轮上分别设置有开口槽，玻璃片固定在开口槽上。

The driving gear and the driven gear are respectively provided with an open groove , and the glass sheet is fixed onto the open groove .

仔细分析了某型摩托车里程表主动齿轮（形式上相当于一个渐开线圆柱蜗杆）的轴向齿形。

The axial profile of an odometer driving gear ( in form it 's equal to an involute helicoid worm ) in a certain model motorcycle is carefully analysed .