高压成型

  • 网络High Pressure Forming
高压成型高压成型
  1. 制造高质量的花岗岩砖均采用优质原料、高铝硬质研磨介质、高压成型及快速烧成。

    Superior raw materials , high alumina hard material used as grinding media , high pressure forming and fast firing are used for making high quality granite tiles recently .

  2. 内高压成型设备液压控制系统研究

    Research on Hydraulic Control System of Internal High-pressure Forming Equipment

  3. 钨的超高压成型与低温烧结

    Ultrapressure Forming and Low-Temperature Sintering of Tungsten

  4. 补偿器接头内高压成型数值仿真

    Hydroforming of Compensator Joints Numerical Simulation

  5. 产品特点:硅莫砖以阳泉特级矾土熟料和碳化硅为主要原料,经高压成型、高温烧结而成。

    Properties of Products : The raw materials for this product are Yangquan bauxite and SiC , being pressed and sintered .

  6. 无粘结剂高压成型时,随着煤的粒度的减小,型煤强度增大;

    The briquette strength is increased along with the feed coal particle size decreasing at the without binder and high-pressure briquetting process condition .

  7. 通过介绍内高压成型设备的工作原理和设备组成,分析了设备中各个系统的特点。

    Through the introduction of the working principle and composition of the Internal high-pressure forming equipment , this paper has analyzed the characteristics of each system of the equipment .

  8. 介绍了内高压成型原理,对内高压成型设备液压控制系统进行了研究,最后给出了试验结果,并对试验结果进行了分析。

    The principle of internal high-pressure forming was introduced , and the hydraulic control system of internal high-pressure forming equipment was researched . Finally , some test results and their analyses were given .

  9. 产品特点:高炉用莫来石砖采用人工电熔或烧结莫来石原料为主要原料,经高压成型、高温烧结而成,主要矿物组成为莫来石。

    Properties of Products : Mullite bricks for blast furnaces were made from fused or sintered mullite , being high pressure pressed and sintered in high temperature , main minerals are mullite stones .

  10. 生物质燃料常温高压致密成型技术及成型机理研究

    The Studies of Biomass Solidifying Technology and Principle with High Pressure on Natural Conditions for Bio-fuel Making

  11. 本文的研究目的是以节能、低成本为出发点,通过对常温高压致密成型影响因素及成型机理的研究,找出使成型效果较好的影响因素的参数范围,探讨成型机理。

    The purpose of this study is finding out the parameter scope of solidifying factors , and groping for solidifying principle , which take energy efficiency , low-cost as springboard .

  12. 生物质常温高压致密成型技术与传统的热压成型相比,具有节能、不破坏生物质内部结构的优点,有较好的发展前景。

    Compared with the traditional heating solidification shaping technology , bio-fuel solidification shaping technology with high pressure in general conditions has many merits , such as economy , not destroying the interior fabric of the biomass , it will have a good foreground .

  13. 国外高压对辊成型机的设计及其新进展

    Design of foreign HP dual roller shaping machine and its new development

  14. 指出选用粘结剂,采用高压真空挤出成型工艺可提高半成品干燥强度;

    It points out that the high pressure vacuum extruded forming process with selected glue can increase the dry strength of semi-product .

  15. 以东芝、川口注塑机、小川高压制作所高压成型装置,及大量成型事例为依托,论述了PFP(PartialFrameProces)注射成型法的基本原理;讨论了注塑变量与PFP成型的关系;

    The principle of partial frame process ( PFP ) is described based on Toshiba and Kawaguchi injection moulding machines and a high pressure device from Ogawa Highpressure Manufacture Institute .

  16. 复合材料高压气瓶用预成型织物的设计与织造

    Structural design and weaving of preformed fabric for manufacturing composite high-pressure cylinder for gases

  17. 内高压成形及热成型因特拉肯的内高压成形压机系统是在生产或工艺开发应用。

    Hydroforming & Warm FormingInterlaken 's Hydroforming Press Systems are for use in production or process development applications .