载货汽车

Air（初三适用）五十铃轻型载货汽车的空调系统

Air Condition System of Isuzu Light Duty Truck

基于ADAMS的重型载货汽车可靠性仿真与试验研究

Reliability Simulation and Test of Heavy-duty Truck Based on ADAMS

载货汽车左/右前扶手下加强板冲压工艺制定及CAE分析

Development of Stamping Processes and CAE Analysis of the Lower Reinforcing Plate of the Left / Right Front Armrest of a Truck

本文将试验手段和CAE仿真技术相结合，以某重型载货汽车为研究对象，构建了一种耐久性虚拟试验方法。

In this paper , a virtual durability test method which combines test method and computer aided engineering for a heavy truck was established .

春兰NCL系列载货汽车柴油发动机预热系统

Warm-up System of Diesel Motor on CHUNLAN NCL Truck Series

应用能量分析的方法，以轿车和载货汽车为例，研究了混合动力汽车（HEV）与传统燃油发动机汽车的燃油经济性。

This paper studied the fuel economy of conventional vehicle and hybrid electric vehicle ( HEV ) by the method of energy analyzing for car and truck .

介绍春兰NCL系列载货汽车电气系统的结构、配置及电路原理。

This paper introduces the structure , configuration and circuit principles of the electrical system of CHUNLAN truck series .

从斯堪尼亚（SCANIA）牌汽车看我国载货汽车电系的差距

Seeing Chinese Truck Electronics Gap from SCANIA car

提出了根据发动机转速信号来识别不同制动工况的方法，制定了相应的换挡控制策略，并在装有AMT的某重型载货汽车上进行了实车制动试验。

According to the different brake conditions identified by the rotating speed of engine , the corresponding shift control strategy is established and a brake test is performed on an AMT heavy truck .

使用AltairHyperMesh软件，对国内某座椅厂的载货汽车机械可调式座椅进行有限元模型的建立。

In chapter 2 , the mechanical suspended truck seat system model is set up with Altair HyperMesh software based on the digested software .

利用MSCADAMS/Car软件建立载货汽车后空气悬架系统多体动力学模型，仿真计算了悬架垂直刚度特性，证明模型的正确性。

A rear air suspension multi-body dynamics virtual prototype model is created with MSC Adams / Car . The vertical rate rigid characteristics of the rear air suspension are simulated and the correctness of the model is proved .

其次，以某重型载货汽车车架结构为研究对象，利用ANSYS建立了车架结构有限元的实体单元模型，对车架建模过程进行了研究；

Secondly , it took some carrier car frame structure as research object , established the entity unit model by using ANSYS , and made a research on the frame modeling process ; model . This improved mixing dielectric model yields an excellent fit to measured data .

介绍了解放CA1170P2K1L2型载货汽车动力转向机构的组成及工作原理。

Comprising and work principle of the power steering system of JIEFANG truck CA1170P2K1L2 are introduced .

在装有AMT的某重型载货汽车上进行了有、无柔性控制的换挡对比试验，试验结果表明，该柔性控制方法可以有效避免换挡卡滞，提高了AMT车辆的换挡成功率。

The contrast tests of one heavy loading AMT vehicle with the flexible control and without it were done , and the test results show that this method can avoid the shift clamping stagnation and increase the shift success rate of AMT vehicle .

一些更大的轻型载货汽车和SUV，像雪佛兰HHR，看起来就好像他们用轮胎打气泵和注入大量附属品弄成的夸张样。

Some of the bigger " light trucks " and SUVs , like the Chevrolet HHR , look as if they have been inflated with tyre pumps and injected with large quantities of lard .

分析了EQ140型载货汽车使用中飞轮壳的损坏特征及原因，并对防止其损坏提出了几点建议。

In this paper the features and causes of flywheel housing damage in service of EQ140 trucks are studied , some proposals to prevent from damaging are raised as well .

介绍了玛达拉&里亚茨MT4、MS24系列载货汽车液压助力式转向器的结构特点、工作原理、使用技术，以及常见故障的诊断与排除方法。

This paper describes the structural features , working principle , application , diagnosis and remedy of commonly seen troubles of the MT4 and MS24 series hydraulic power steering for Madala-Liaz trucks .

以简化的大型载货汽车模型GTS为研究对象，采用RNGk-ε湍流模型和混合网格技术，分别模拟了气流流过驾驶室与货厢之间不同长度的间隙时产生的流场形态。

The effects of the gap between the driver cab and the freight body of the heavy-duty truck on its aerodynamic characteristics were simulated by means of a simplified truck model ground transportation system ( GTS ) using the RNG k - ε turbulence model and hybrid mesh technique .

介绍了某载货汽车左/右前扶手下加强板冲压工艺设计过程，利用Autoform分析软件对板料成形过程进行了有限元模拟分析。

Processes of stamping process design of the lower reinforcing plate of the left / right front armrest of a truck are introduced . The forming process of the sheet material is simulated and analyzed with AUTOFORM finite element analysis software .

利用前后置处理软件MSC/PATRAN（V8.5）和有限元求解器MSC/PATRANADVANCED-FEA（V8.5）能够对轻型载货汽车钢板弹簧的模拟方式进行若干情况的分析和比较，得出能较好模拟真实结构的建模方式。

With the preprocessing and post-processing software MSC / PATRAN ( V8.5 ) and the FEM solver MSC / PATRAN ADVANCED-FEA ( V8.5 ), different models can be analyzed and compared , then the better models which can rationally simulate the actual structure can be obtained .

因此，对重型载货汽车动力学的研究格外受到重视。

Therefore , the study of heavy-duty truck dynamics is important .

基于大样本数据的中型载货汽车使用可靠性研究

Research of Medium-duty Trucks ' Operational Reliability Based on Sample Data

重型载货汽车变速器远距离操纵机构设计

Design of Gearbox 's Long-Distance Control Mechanism in Heavy Duty Truck

中型载货汽车轮胎表面温度的稳态特性

Steady characteristic of surface temperature of tire of middle duty truck

运载货物用机动车辆载货汽车子午线轮胎

Motor vehicle for the transport of goods radial tyre of truck

提高东风平头载货汽车点火锁可靠性

Enhancing the Reliability of the Ignition Switch on DONGFENG COE Truck

连接工艺对载货汽车车门强度和刚度的影响

Effect of joining technology on strength and stiffness of truck doors

载货汽车运行燃料消耗量计算方法研究

Study on Calculation Method for Fuel Consumption of Trucks in Operation

轻型载货汽车半轴疲劳寿命预测

Forecast of Fatigue Life of Light Truck Driving Half Shaft

基于有限元方法的载货汽车驱动桥壳分析

Analysis on the Truck Drive Axle Housing with the Finite Element Simulation