转换单元

必须对其进行验证，因为它现在是JSP转换单元的一部分，必须符合JSP语法规则。

It must be validated , because it is now part of the JSP translation unit and must meet JSP syntax rules .

RS-232与CAN总线协议转换单元设计

Design of Protocol Conversion Unit between RS-232 and CAN Bus

基于DSP的电空转换单元控制器

Electric-pneumatic unit controllers based on DSP

大型LED（发光二极管）显示屏由计算机、数据转换单元与显示单元组成。

The LED ( light-emitting diode ) dot matrix screen is constitute of computer , data transfer unit and display unit .

传统DDFS中的相幅转换单元是基于查找表实现的，精度受面积的制约。

The unit of Phase to Amplitude in conventional DDFS always uses Look-Up-Table ( LUT ), however the precision is restricted by area .

高温气冷堆HTGR-10能量转换单元中压气机气动性能试验研究

Testing compressor aerodynamic performance in the power conversion unit of HTGR-10

硬件电路的设计包括语音数据采集及回放单元，语音压缩解压单元，数据处理、传送及接收单元，时钟同步单元，键盘及显示单元和RS-232串口电平转换单元等几个部分。

The hardware design includes the speech data sampling and reconstruction unit , encoder and decoder unit , data processing and transmission unit , clock synchronous unit , keyboard and display unit , and RS-232 converter unit .

新型电光调谐型ROADM通过超高速调节其偏振转换单元与波长调谐单元的电极电压来实现特定波长的上下载，调谐速度达到了纳秒量级。

A new kind of electro-optical tunable ROADM was developed , it can upload and download specific carrier wave by regulating the voltages of its polarization conversion unit and wavelength tuning unit .

民用飞机液压系统元件EDP（发动机驱动泵）、ACMP（交流电动泵）、PTU（能量转换单元）为系统提供液压能，是整个液压系统的核心元件。

Commercial aircraft hydraulic components-EDP ( Engine driven pump ), ACMP ( AC-motor driven pump ), PTU ( Power Transfer Unit ) are the key components , supplying the system with hydraulic energy .

讨论了0.9μm标准单元正向设计流程中当电路中存在5V和3V两种电压时芯片的设计方法，包括网表产生与验证，版图设计，电压转换单元的加入原则。

The chip design methods while two different voltages exist in circuit in 0 9 μ m standard cell top down design flow are discussed , including netlist generation and verification , layout design , and the principles for voltage conversion cells insertion .

光纤通信系统中2/8转换单元的设计

2 / 8 change unit design for the optical fibre communication system

煤矿风机监测系统中传感器智能转换单元研制

Development of sensor intelligent conversion unit used in coal mine ventilator monitoring system

太阳能非碳冶金电热转换单元结构设计及热模拟研究

Structure Design and Thermal Simulation Study on Electric Thermal conversion Unit In Solar Non-carbon Metallurgy

该方案将系统分为车辆检测器，接收机与中继器以及数据转换单元三部分。

The system is divided into threemodules : vehicle detectors , receiver ( repeater ) and data conversion unit .

同时还采用在不同载荷步之间转换单元材料物理性质，以考虑激光烧结过程中的局部热源输入作用。

A method to transform element material properties between load steps is also taken for consideration of the regional-input high-power laser beam .

评价主控机由主控、数据存储及232电平转换单元、电源输入部分及485总线接口单组成。

Evaluating host is composed of main control , data storage , 232 level conversion unit , power input and 485 bus interface .

借助于温度节点计算结果，并转换单元类型，仿真计算了放电区域的热应力集中，热变形分布大小。

The thermal stress concentration and the thermal strain distribution is simulated and calculated by the temperature nodes calculation result and the element types change .

对设计出来的整个系统进行测试，能实现对光电转换单元进行参数的自动检测、控制调节功能，整个系统运行稳定，达到了预期的目标。

The system can achieve the function of detecting and regulating the photoelectric conversion unit . The system works stable , and it reaches the desired goal .

模数转换单元的设计和实现，包括器件的选型，模数转换器的缓冲器设计，计算实际性能参数，及其硬件实现；

Designing and realizing of Analog-Digital Conversion Unit , including choosing the IC , designing the Buffer for ADC , calculating the practice performance parameter in the practice .

详细地介绍了测试系统的软硬件设计，智能逻辑转换单元的构成，以及测试功能的实现过程。

The design of the hardware and software of the testing system , the composing of intelligent logic conversion unit and the realization of system function are detailedly introduced .

电空转换单元是新型微机直通式电空制动机的重要组成部分，也是空电联合制动的基础。

An electric-pneumatic ( EP ) unit is the important part of a new type of computer direct EP brake , and also is the base of EP blend braking .

硬件结构主要包括总体时序控制单元、存储单元及其时序发生器、串并转换单元、移位器、选通器、运算单元和级联加法器。

The main structure of the hardware including top timing control unit , bram and its timing generator , serial to parallel converter , shift register , multiplexer , processing element and multi-level adders .

仿真测试系统硬件电路由三部分组成：人机接口单元、数模转换单元、功率放大与反馈单元，能够实现闭环测试方法和自动测试功能。

The hardware circuit of protection testing system under study is composed of three units ; those are man-machine interface unit , digital to analog converter unit , and power amplifier and feedback unit .

文章最后同样给出了信号发生装置、电空转换单元以及两者联合制动的试验过程以及结果分析，提供的试验数据和分析为整个制动系统可靠运行奠定了坚实的科学基础。

At the last of this paper , it shows us research and analysis on signal occurring device experiments , electro-pneumatic unit experiments and signal occurring device and EP united experiments , whose data make a solid base for function of this whole brake system .

文章按照整个制动系统的结构分章节作了较为详细的叙述，对关键的电气控制设备例如电空转换单元、逻辑控制器、信号发生装置以及电控制单元都给出了系统设计和控制方法。

This paper amply describes the structure of braking system in several chapters , it also gives particular design and control method of the critical electrical control components , such as electro-pneumatic unit , logical control unit , signal occurring device , and microcomputer brake control unit , etc.

本文介绍一种用于便携式含氢量测定仪的单片机测控系统，重点讨论该系统的单片机扩展单元、信号调理单元、模/数转换单元、真空系统控制单元和系统软件的设计方法。

A single-chip-computer testing and controlling system for on-line testing of hydrogen content is introduced and the system expanding unit , the signal modulating unit , A / D converting unit , the vacuum control unit and the design method of the system software are described in detail .

包传输（或包转换）单元（PacketTransferUnit，PTE）是网络处理器中负责IP包协议处理的核心模块，完成IP包在转发过程中的分析处理。

Packet Transfer Unit ( PTE ) is one of the most important units of NP , which is responsible for packet analyzing and processing .

RTD室温下的峰谷电流比为5.2∶1，峰值电流密度为22.5kA/cm2.HEMT采用1μm栅长，阈值电压为-1V.设计电路称为单稳态-双稳态转换逻辑单元（MOBILE）。

The RTD has a room temperature peak-to-valley ratio of 5.2 ∶ 1 with a peak current density of 22.5kA/cm2.The HEMT has a 1 μ m gate length with a-1V threshold voltage . A logic circuit called a monostable-to-bistable transition logic element ( MOBILE ) circuit is developed .

对您想要转换子单元的方式进行配置。

Configure how you want the subunits to be converted .

这样，我们就将“路由”单元和“管道”单元与“转换”单元组装在了一起。

So we compose the " routing " brick with " pipe " and " transformation " bricks .