试模

  • 网络TEST MOLD;test mode;try-out;Die trial
试模试模
  1. 开发热流道辅助设计软件对缩短热流道设计周期,降低试模返修率等具有重要的意义。

    In order to shorten the design circle of hot runner and decrease the rework probability of test mold , it is important to develop the design software on Hot Runner CAD .

  2. 通常浇注系统的设计是依靠设计人员的经验,通过现场不断的试模、修模来调整浇口、流道的尺寸,以找到符合需求的设计。

    Usually , designers determine runner system by their experiment , and adjust the dimension of gate and runner by die trial and die repairing constantly to find the best plan .

  3. 汽车覆盖件成型模试模调整时R角不良问题处理重力对板材滚弯成形半径的影响

    The Effects of the Gravity on the Plate Roll Forming Radius

  4. 经过CAE拉深软件的模拟分析,对于拉深不足的区域采用增加拉深筋的方式,通过试模最终加工出合格的零件。

    Through simulated analysis of CAE simulation software , It applies drawing ribs to insufficiently drawing area . It produces qualified parts through testing die .

  5. 注塑成型CAE技术可以帮助工程师对塑件的注塑成型工艺进行优化,以减少反复试模修模的次数,缩短产品的生产周期。

    Injection molding CAE technology can help engineers to plastics molding process optimization , to reduce repeated the number of mold testing molds , shortened product production cycle .

  6. 同时,CAE技术是开展研究的平台,在分析过程中的广泛运用,充分说明其在缩短设计周期,提高一次试模成功率方面具有重要作用。

    In addition to , the use of CAE technology shows that it plays an important role in reducing the product developing cycle and improving success in die adjustment one time .

  7. 利用注塑模CAE技术可在模具制造之前,对模具设计方案进行分析和模拟来代替实际的试模,预测设计中潜在的缺陷并及时修改。

    Using CAE technique , the mold design can be analyzed and simulated in computer to replace the actual mold trial-and-error and potential defect can be predicted and corrected before mold is made .

  8. 经过多个方案的比较,最终得出比较合理的设计方案,采用CAE模拟技术可以减少试模、修模的次数,并缩短模具设计与制造周期,降低生产成本。

    Finally the best project is detained by comparing various ways . Introducing the CAE can reduce the times of molding test and molding mend , shorten the circle of the design and manufacture of mold , and lessen the cost of production .

  9. 另外本文应用基于CAI技术对有限元仿真结果数据进行检测,可提前评估回弹情况,有利于及时对回弹进行补偿,避免过早试模。

    Comprehensive , can accurate and efficient assessments springback of products ; In addition , this paper is based on CAI technology to detect the finite element simulation results data , which can early assess springback , conducive to the timely springback compensation , avoid premature tryout . 3 .

  10. 本文介绍了虚拟试模技术及其在板成型中的应用,本研究所采用的有限元软件是PAM-STAMP。

    The virtual die tryout technology and its application in sheet metal forming are described . The FEM program used in this research is PAM-STAMP .

  11. 其中由正交法设计得到实验样本,由软试模提取模具的SDV值,将其作为优化目标。

    It takes design experiment samples by orthogonal plan method and regards the SDV values which come from soft trying die as goal of optimizing .

  12. 在模拟结果的基础上一次试模成功,灌水器制品的流道部分精度达到±0.01mm。

    On the basis of the injection simulations , the work of molding trial was succeeded at one time , and the precision of the emitter channel was lower than ± 0.01 mm .

  13. 对混凝土试模管理的重要性

    The management of test mould of concrete cannot be neglected

  14. 经过实际试模后进一步验证了分析结果的准确性。

    The try-mold validates the veracity of the result analyzed .

  15. 最后,模具零件进行加工、装配以及试模。

    Finally , the mold parts processing , assembly and test mode .

  16. 最后通过试模后,该模具能够挤压出完全合格的铝型材。

    Finally , after trial , the die can extrude qualified part .

  17. 我们将迟一个星期试模。

    Our mold testing will be postponed for one week .

  18. 外壳注射模的试模分析

    Analysis of Testing Injection Mold for the Outer Covering

  19. 板材成型的虚拟试模技术

    Virtual die tryout technology for sheet metal forming

  20. 汽车覆盖件试模调整问题

    Problems of Automotive Cover Parts Die s-test Adjustment

  21. 负责试模,安排每日试模工作。

    Responsible for the tool trial run , arrange the daily trial run work .

  22. 注射模试模工艺过程

    Technology of Trying Mold for Injection Mold

  23. 一次试模成功,塑件质量好。

    It succeeds in once testing module , and the plastic parts quality is good .

  24. 精密滚子的成形一次试模成功,质量良好,已投入生产使用。

    The die for the precision roller was put to use and made good quality products .

  25. 适用范围:注塑部量产中的模具,不含试模模具。

    Application arrange : the mold for the mass production , not for the trial mold .

  26. 复杂箱体抽芯结构模具试模过程中对注塑机的改造

    The Reconstruction of Injection Molding Machine for the Trial of a Mould with Complicated Core-Pulling Mechanism

  27. 有时仅仅依靠传统的经验、技术诀窍和不断试模的方法,仍不能有效地解决问题。

    The problem can 't be solved effectively by experience , technical knack or repetitious test .

  28. 然而传统的注塑模设计方法主要靠经验来反复调模和试模,这样不仅浪费大量的人力和物力,而且导致产品的研发周期过长。

    However the traditional method of designing injection molding mainly depends on experience to test and adjust molding .

  29. 辅助操作器械包括:A、同样型号尺寸的三种解剖型试模;

    The assistant manipulating appliance are : A : the same size just as the AACR anatomy module ;

  30. 模具经试模后,可以大批量进行生产质量稳定的合格产品。

    Therefore , this mould , after the stage of testing , could cast qualified products in large-scale manner .