翻边工艺

F型强火力燃气灶面板成形、翻边工艺及其模具

Forming , flanging and die for panel in F type gas kitchen with strong fire

根据翻边工艺计算翻边系数K，计算分析拉深次数。

The flanging coefficient K was calculated according to the flanging process . Drawing times was analyzed and calculated .

翻边工艺的试验研究及数值模拟

Experimental Study and Numeric Simulation of Flanging Process in Sheet Stamping Forming

板料大变形程度内凹翻边工艺研究

Study on Inner - concave Flanging within the Large Deformation of Sheet

小型圆筒件的冷翻边工艺研究

Study on the Process of Cold Duplicating of Plate Blank for Small Ring

小型轴承套圈板坯冷翻边工艺研究

Study on the process of cold duplicating of plate blank for small bearing ring

车轮轮辐中心孔翻边工艺参数优化

Optimization of process parameters in center hole of the wheel ′ s disc burring

汽车发动机罩冲压成形后翻边工艺机械自动化一直是困扰汽车制造商的技术难题。

The mechanical automation of bending technique is the troublesome problem to car ′ s manufacturer .

汽车消声器筒体翻边工艺及模具设计汽车消声器筒体翻边加工过程的数值模拟

Barrel Purfle Manufacturing and Mould Design of Automobile Noise Silencer Numerical Simulation of Extrusion Process for Moter Silencer Tubes

表明这种研究对翻边工艺理论和实践的发展具有指导意义。

So , the result of the study has an important guiding significance for the development of academic research and engineering practice of flanging process .

本系列风机的叶片采用特殊扭曲孤度设计，机壳采用法兰翻边工艺，使风机噪音更低，风量更大等特点。

SF ( B ) series adopt special twisted blade design and flange flanging casing , which makes the noise lower and the air volume larger .

然而，现今的研究中，相对于冲裁、拉深、弯曲等冲压基本工序而言，关于翻边工艺方面的研究比较少，与翻边有关的文献资料更为有限。

However , compared with other stamping processes such as blanking , drawing and bending , the investigation about flanging process is very limited in existing documents .

对变薄翻边工艺受力情况和变形性质进行了分析，介绍了一种变薄翻边力的主应力计算方法。

In this paper , state of stress and deformation nature of thinning flanging process are analysed . The Slab Method for calculation of Flanging Load is introduced .

介绍了钢板翻边工艺中预冲孔直径的等面积计算与工艺验证结合的确定方法。

This paper introduced the method to confirm the combination of the equal area calculation of the pre punching hole in the technology of the turn over of steel plate .

首先从CAD与CAE的集成技术、SolidWorks二次开发、修边和翻边成形工艺以及采用的有限元基本理论等方面深入研究了系统的开发基础。

Firstly , the development foundation of the system was deeply studied , based on integration of CAD and CAE , redevelopment of SolidWorks , trimming and flanging process and basic theory of FEM .

讨论了聚四氟乙烯焊接、热拉伸、翻边等工艺技术。

The welding , hot-stretching and curling technologies of FTFE are discussed .

对固定支架成形的变薄引伸、翻边的工艺进行了分析，对出现的问题提出了解决办法。

This paper analyzes the stretching and turning edge process of big deformation for an array turning edge-hole and proposes some solutions to the problems .

运用金属塑性成形原理，通过六氟化硫断路器壳体孔翻边的工艺计算，介绍了一种曲面孔翻边预冲孔的一种近似工艺计算方法。

Using metal plasticity forming theory , by the technology calculation of sulfur hexafluoride breaker shell flanging , a technology calculation method was introduced about pre-punching flanging .

旋挤法翻边孔加工工艺及其主要参数的优化

Revolving Extrusion Process for Flanged Holes and Optimization of Its Main Parameters

车轮内孔翻边模翻边工艺计算

Technology calculation to turring model of wheel inner hole

针对方形翅片管加工特点，确定了翅片翻边的相关工艺尺寸，提出了套片式翅片管的热套工艺方案。

The relative sizes of the turn down rims of the fins were determined for the processing characteristics of square finned tubes , the shrink fit technology program of the casing fin tubes was proposed .

把人工神经网络（ANN）和遗传算法（GA）相结合进行工艺优化设计，研究了S形件翻边成形中的工艺参数优化。

Technological parameter optimization design was researched by combining ANN and GA in forming S-shaped pieces .

12×4J轮辐翻边变形分析及工艺改进

Strain analysis of 12 × 4J wheel burring process and improvement of technology

高翻边类零件成形工艺仿真优化及试验研究绳类的断裂强力和断裂伸长率的测定法

Study on Optimization and Experimental Research of the Forming Process of the Product with High Flange testing method for breaking strength and elongation of cords

本文就这种翻边接头的几种形式、模具设计以及翻边加工的工艺过程作了介绍。

Several types of flanged nozzeles , die design and flanging process are informed .

本文阐述了发动机罩翻边的技术原理，详细介绍了发动机罩翻边机的总体设计思路及方案，为同类零部件的翻边工艺揭示了一种行之有效的解决办法。

This paper expounds the technique theory of bending for car ′ s engine bonnet , particularly introduces the general design methods of bending machine for car ′ s engine bonnet .

对车轮内孔翻边极限翻边因数的主要影响因素做了讨论，在此基础上，对12×4J车轮轮辐中心孔翻边模翻边进行了工艺计算。

The turring parameter of turring model of wheel inner hole is discussed in this paper , on th basis of this , the technology calculation of 12 × 4J wheel hole turring process is carried on in this paper .