线间距

选择合适的等值线间距（临界值）可以有效地发现粗差，求得各GPS点的正常高。

Selecting suitable isoline interval ( critical value ) may find gross error effectively , the normal height of GPS ' points is get .

在IC的制造过程中，由于工艺的随机扰动，过刻蚀和欠刻蚀造成了导线条的宽度和线间距的变化。

Over etching or under etching in IC process causes the variation of the linewidth and spacing between two parallel lines because of the random disturbance of the process .

中心站用移动接触网时6.5m线间距可行性探讨

Discussion on Feasibility of Adoption of 6.5 m Line Spacing During Mobile Catenary Used in Center Station

地铁3.4m线间距单渡线总体方案研究

Research on Overall Program of Laying Single Crossover with 3.4 m Distance between Centers of Lines for Metro

同时，我们对不同线间距以及不同线宽的互连线结构的电特性进行仿真，并且进行相应的TDDB失效测试。

The electrical characters of interconnect lines with different line space and width are simulated with the ISE . The TDDB failure tests are operated on interconnect samples .

线间距变化的双线铁路曲线桥梁布置方法

Layout of double track curved bridge with different midway between tracks

关于电力机务段定修库线间距的探讨

Discussion on Distances Between the Lines in Electric Locomotive Repair Depot

计算机绘图在求解线间距中的应用

The Computer Graphics ' Application in Working out the Distance Between Lines

轻轨线路采用正常线间距单渡线的研究

A Research on the Single Crossover Adopted on LRT Line

电晕线间距优化布置的试验研究

Experimental study of optimum wire spacings for different plate spacings of EP

两通道直总线连接器。可调整线间距。

2-channel straight bus connector . Line spacing is adjustable .

次要刻度线间距必须小于主要刻度线间距。

Minor unit must be less than or equal to major unit .

测线间距的确定是海洋磁探测技术设计的重要内容。

Defining space between survey lines is essential to marine magnetic detection design .

带箭头和可调线间距的双线连接线。

Double-line connector with arrowheads and adjustable line spacing .

水下磁目标探测线间距确定方法

The Method of Defining Survey Lines Space in Marine Magnetic Detection of Underwater Object

一种线间距的获取方法

Method for finding out distances between railway tracks

主要讨论线路平面线间距的计算问题，对传统的坐标法计算有新的思路。

This paper developed the traditional coordinate method in calculating distance between double-line railway .

抛物面研磨实验中转轴与梁中心线间距的确定

Estimating the Distance Between Rotating Axis and Center Line of Bar in Paraboloid Lapping Experiment

测线间距，一般地说在寻找石油时要比矿物勘探中大。

The line spacing will generally be greater in searching for oil than in mining exploration .

小线间距施工隧道爆破地震影响下既有隧道围岩线性动力分析

Linear dynamic analysis on ROCK-MEDIA of old tunnel affected by blasting vibration of new tunnel with small line-clearance

D型便梁在小半径曲线及小线间距区段的应用与计算

Application of Type D Auxiliary Girder to Small Radius Curves and Sections of Small Distance Between Centers of Tracks

线路圆曲线半径、缓和曲线长度和线间距标准制定依据的介绍

Basis for Determining the Standard for Circular Curve Radius , Length of Transition Curve , and Distance between Centers of Tracks

文中概述了本隧道线间距的设计依据和理论论证，并对设计计算方法和现场试验结果进行了分析。

This paper describes the design basis , theory and the design calculation method , moreover , analyzes field test results .

过站区为双线隧道，隧道跨度大、埋深浅、线间距小，采用矿山法施工难度和风险极大。

The connecting tunnels constructed using mining method have a large span 、 a shallow coverage and a little distance between two lines .

接收线间距与震源线间距之比的余数决定了接收线方向和震源方向所期望的次反射面元。

The remainder after the ratio of receiving-line spacing to source-line spacing determines the expected sub-bins in directions of receiving line or source line .

同时研究了芯片与微带线间距的互连、微带线制作、材料的可焊性及焊接过程等制造技术。

And other manufacturing technologies-interconnect between the chip and microstrip 、 manufacture of microstrip 、 solderability of available materials and soldering process are discussed .

本文介绍了对于梁柱中心线间距大于四分之一柱宽的大偏心梁柱节点所进行的试验研究和计算分析。

Experimental research and analysis of the seismic behavior of reinforced concrete eccentricbeam-column joints with eccentricity larger than one-fourth of the column width are introduced .

提出了以图像灰度为权函数的加权回归计算滑移线间距、滑移带带宽的方法；

A way based on the method of weighted least squares for measuring and calculating the sizes of fatigue slip band and fatigue striation spacing is presented .

仿真结果表明，改变耦合线间距和耦合线宽度，可改变耦合线的耦合系数，从而实现可重构定向耦合器的功能。

The simulated results show that the reconfigurable couplers can be realized by changing the distance between the coupled lines and the width of the coupled lines .

铜电镀工艺后表面的不平整度通常取决于版图关键特征，包括线宽，线间距和金属密度。

The non-planarity of a surface post electroplating process is usually dependent on variations of key layout characteristics including line width , line spacing and metal density .