燃料层

在单元体层燃炉模型炉上，对采用空气分级燃烧技术前后的燃料层温度、烟气中的CO、O2、NOx浓度进行了试验研究。

With a fixed-grate furnace model , the temperature of fuel layer and the concentration of CO , O_2 and NO_x in flue gas were studied respectively before and after application of the air-staged combustion technology .

通过煤气炉冷炉测定，了解煤气炉内原料粒径沿床层截面分布情况，炉渣下降情况，炉箅结构对燃料层气化的影响等物料性状。

Through gasifier calibration , the feed distribution along the cross sections , the falling down of dregs , and the influence of grate structure to the gasification of fuel layer can be understood .

生物质燃料层热解过程的传热传质模型研究

Heat and mass transfer in pyrolysis process of biomass fuel bed

惯性约束核聚变用低温冷冻靶燃料层厚度的确定

Calculation about the fuel thickness of ICF target

通过数值模拟，得出了燃料层热解过程中的温度场的分布、层内固体密度的变化以及气体的生成规律。

The temperature distribution , density and gas yield of the biomass fuel bed were obtained by numerical simulation .

辐射加热条件下生物质燃料层热解过程的传热传质

Research on the heat and mass transfer in the pyrolysis process of the biomass fuel bed under radiant heating

典型生物质燃料层燃燃烧特性的试验研究超燃冲压发动机支板喷射燃料的燃烧过程试验

Grate Firing Characteristics of Typical Biomass Fuels Experimental study on the combustion and flow process in a scramjet with strut injector

在已热解区，燃料层内约30%的物质形成焦炭，约有70%左右的固体物质转变为挥发分气体。

In the coked zone , about 70 % biomass turn into combustible gas , the leaved ( 30 % ) is coke .

通过分析生物质热解过程的传热传质特点，建立了生物质燃料层热解过程的传热传质数学模型。

A mathematical model for the heat and mass transfer in the pyrolysis process of the biomass fuel bed was developed in this paper . Heat and mass transfer characteristics of the process were discussed .

以及，在工作温度下，燃料液体层的厚度和充填温度、充填压力之间的对应关系。

The connection between the thickness of liquid fuel layer and the filling temperature and gas press is given by usage of BWR equation .

以运载火箭液氢/液氧燃料隔离层共底构件为典型零件，采用常规的数控加工方法已无法保证精度要求。

In this paper , the fuel isolated layer structure of launch vehicle is taken as the typical component , which separates the liquid Hydrogen from liquid Oxygen . The conventional CNC manufacturing techniques are very difficult to meet the requirements of the precision .

利用该仪器实测了高温气冷堆包覆燃料颗粒SiC层（直径<1mm）的弹性模量。

The Young 's Modulus of SiC layers of coated fuel particles for HTGR are measured .

Ag在质子交换膜燃料电池催化层中富氧作用的研究

Research of the Oxygen Enrichment of Ag in the Proton Exchange Membrane Fuel Cell Catalyst Layer

X射线照相法测量包覆燃料颗粒包覆层的厚度和UO2核芯的直径

X ray projection microradiography for measurement of coating layer thickness and UO 2 kernel diameter

瓷相磨片法测量高温气冷堆燃料微球包覆层的厚度

The Thickness Measurement of Coatings for HTGR Coated Fuel Particles by Ceramography Method

质子交换膜燃料电池扩散层实验及模型研究

Experimental and Modeling Research of GDL of PEMFC

高水分燃料的沸腾层烟气热平衡方程

A Thermal Energy Balance Equation Obtained for the Flue Gases of a Fluidized Bed When High moisture Fuels Were Fired

镅的器壁吸附及其对扩散池实验的影响质子交换膜燃料电池扩散层实验及模型研究

Sorption of Americium on Container Wall and Its Influence on Through-Diffusion Cell Tests Experimental and Modeling Research of GDL of PEMFC

通过乳液法成功制备了亲疏水性可调的燃料电池催化层，其润湿角为78°～130°。

The hydrophilic-hydrophobic adjustable catalyst layers , with contact angle of 78 °~ 130 °, were prepared successfully by using of microemulsion method .

给出了低浓铀燃料元件结合层超声反射回波相位幅度信息理论分析和计算方法，也讨论了不同结合率对回波相位与幅度的作用。

The theoretical analysis and calculation for the amplitude and phase of ultrasonic echoes from the bonding layers of low enriched fuel elements are introduced . The effect of different bonding rates on the amplitude and phase is also described .

PEM燃料电池阴极催化剂层的模型及性能分析

Model of Cathode Catalyst Layer and Analysis on Performance of PEM Fuel Cells

制备了直接甲醇燃料电池双催化层阴极，双催化层由内催化层Pt黑和外催化层40%Pt/C构成。

A novel cathode with double-layered catalyst layer for direct methanol fuel cell ( DMFC ) was fabricated , which consisted of Pt black inner catalyst layer and 40 % Pt / C outer catalyst layer .

采用大气等离子喷涂技术，以活性炭粉作为成孔材料，获得了薄且多孔的中温固体氧化物燃料电池SOFC阳极层。

Air plasma spray technique was used to gain a thin and porous anode layer of intermediate temperature solid oxide fuel cell SOFC by taking charcoal active powder as pore-forming agent in this paper .

轻质燃料油表面覆盖层降耗技术研究

Study on Control Loss Technology of Surface Cover of Light Fuel

燃料电池电极扩散层碳纸性能评价

Carbon Paper Performance Evaluation as Fuel Cell Electrode Diffuse Layer

直接甲醇燃料电池双催化层阳极的稳定性研究

Durability study of double catalytic layer anode for direct methanol fuel cell

燃料电池电极扩散层电阻率-温度特性

Study on resistivity - temperature properties of diffusion layer

高温气冷堆对燃料微球各包覆层的厚度有严格的要求。

The thickness of coatings for the HTGR ( high temperature gas cooled reactor ) coated fuel particles must meet design requirements .

具体公开了一种用于固态聚合物燃料电池的催化剂层，其包括：通过还原铂氧化物获得的催化剂；疏水剂；和质子传导电解质。

Specifically disclosed is a catalyst layer for solid polymer fuel cells which is composed of a catalyst obtained by reducing a platinum oxide , a hydrophobic agent and a proton conducting electrolyte .

刚收获的生物质秸秆燃料水分较大在层燃锅炉直接燃烧时难于着火和稳燃，而采用炉排上部喷入一定比例已磨碎的较干燥的生物质燃料颗粒，可有效解决这些问题。

The harvested fresh biomass fuel contains more moisture , so the ignition and stable combustion is difficult when burned in layer combustion boiler . Injecting a certain amount of grinding and drier biomass fuels into the top of grate can effectively solve these problems .