油道

内部通道有主机油道和冷却水通道。

The inner channel has host oilchannels and the cooling water channel .

而电磁阀又将开启正时链条罩中的油道。

The valves subsequently open oil ducts in the timing chain housing .

大型变压器铁心油道结构及制造工艺

Manufacture and Structure of Oil Duct in Large Transformer Cores

柴油机曲轴斜油道加工专用机床及控制

A Special Machine Tool for Manufacturing Oblique-Oil-Passages on Diesel-Crankshaft and Its Controler

用局部加压方法解决高压油道漏气问题

To Solve Air Leakage Problem of High Pressure Oil Passage by Local Pressurization

发动机缸盖油道密封钢球压装工艺的改进

The Improvement of Seal Steel Ball Press Process for Cylinder Head of Engine

此油道属细长孔，且于轴线成一定的角度。

The lubricative path is a slightness hole which is oblique to the crank .

用相对漏磁法推导多油道圆筒式绕组的电抗电压

Deriving Reactance Voltage of Multi-Oil Ducts Cylindric Winding by Using Relative Magnetic Leakage Method

（气门）挺杆润滑油道明杆平行式双闸滑阀

Tappet oil gallery rising-stem double-disk parallel slide valve

摩托车右曲轴箱油道堵头压入工艺改进

Process improvement on in-pressing of oil path jam in the right shaft case of motorcycle

用插塞封闭油道。

Close off oil ducts with stoppers .

对紊流态下变压器油道内冲流电流的计算进行了研究。

The calculation of streaming current induced by product oil flowing through pipeline is studied .

大变压器线圈典型油道分流合流阻力特性

The Drag Behavior of Diffluent and Confluent Oil Flow along Typical Oil Channels in Large Transformers

电力变压器铁心接地及油道短路故障分析

Malfunction analysis on grounding of iron core and short circuit of oil duct in power transformer

柴油机主油道溢流阀仿真分析

The Simulation and Analysis on the Relief Valve of Diesel Engine On the Paradoxes of Tao

某型号发动机机体主油道滚压的工艺研究

Technical Study of the Rolling Process of the Main Vittae of the Engine Body with a Certain Model

研制了柴油机活塞成型冷却油道的新型水溶芯。

Investigation was made on the water dissolved core of piston of internal combustion engine cooling oil groove .

由计算结果的对比可知，新机油泵能有效地提高主油道压力及供油量，满足润滑要求。

The new pump can effectively improve the oil pressure and fuel supply to meet the lubrication requirements .

本设备专门用于对发动机缸体、缸盖水套及油道的泄漏检测；

This equipment specially used for engine cylinder block and head of water jacket and oil leakage of tao detection .

油道撑条带油道撑条绝缘材料是由矩形撑条与涂胶菱格绝缘纸使用特种胶粘剂粘贴而成；

Oil duct strut insulation material is stuck by rectangular strut and adhesive diamond pattern insulating paper with special adhesive .

在检修发动机时，应对缸体中的油道进行清洁保养。

The oil passages in the cylinder Block should be cleaned out as part of the engine Block Service and Maintenance job .

利用计算模型对两条实验油道的油流带电量进行了计算，计算值和实验值的对比结果表明，计算值和实验值比较吻合。

The streaming current in two experimented pipes was calculated with this model . The calculated and experimented values are in good agreement .

文中介绍了考虑横向油道在内的电感矩阵元素的计算方法。

And the method of calculating the elements of the matrix of the winding-division inductances has taken the effect of the oil ducts into consideration .

用这种水溶芯铸出的冷却油道位置准确，轮廓清晰，其表面粗糙度可达到Ra3.2～6.3μm。

The cast cooling oil groove is precisely positioned and has clear outline , its roughness of surface can reach Ra 3.2 ~ 6.3 μ m.

衬套以防止螺栓孔在数个油道之间形成连通的方式安装到所述螺栓孔中。

A bush is fitted into the bolt hole in such a manner as to prevent the bolt hole from establishing communication between the plurality of oil passages .

利亚兹载货汽车发动机润滑系统的优点为：主油道不在缸体上，缸体的铸造工艺被大大地简化；

The advantages of the Liaz truck engine lubricating system are : Main lubricatinggallery is not in the cylinder block , which makes casting process to be simplified greatly .

最后利用文中推出的计算公式对一实验油道的油流带电进行了计算，结果显示公式得到的值和实验值非常吻合。

Finally , it is used to calculate streaming currents in experimental oil pipes , and the results show that good agreement is obtained between calculated and experimental values .

预润滑装置还可在机油压力不足时继续向油道中补充机油，进一步改善发动机的润滑状态。

Additionally , The pre-lubrication equipment continues replenishing machine oil in oil duct when the pressure of machine oil is below , improving the lubrication state of engine further .

采用反磁钢材料抗漏磁涡流、局部增加油道加强冷却进行改造。

Some measures such as adopting anti-magnet steel material to prevent magnet leakage and eddy flux and increasing local oil channel to enhance cooling effectiveness are taken for improving .

数个油道形成在构成内燃机的阀驱动系统的一部分的摇臂轴的轴体中。

A plurality of oil passages are formed in a shaft body of a rocker shaft , which partially constitutes a valve drive system of an internal combustion engine .