弹簧座

转向齿轮摩擦过大。弹簧座轴承调整螺母

High friction in steering gear . spring seat bearing adjusting nut

弹簧座必须在减震器上居中。

The spring seat must be centred on the vibration damper .

该汽轮机EH执行机构的弹簧座体积比较大，检修时弹簧座装拆困难，影响了装配和维修的效率。

The size of the spring box of this steam turbine 's EH actuator is relatively so big that it is difficult to assemble and disassemble and it affects the efficiency of assembly and maintenance .

拖拉机弹簧座成形模具设计及仿真分析

Die Design and Simulation Analysis of Spring Block in Tractor

QD2853起动机电刷盒弹簧座成型模的改进

Improvement of Generator Electronics Brush Box Spring Place Forming Die

不锈钢弹簧座的离心铸坯-热挤压成形技术

Production of the Stainless Steel Spring Seat by Centrifugal Casting-Heat Extrusion Forming

轿车底盘弹簧座减震器的研制

Development of Absorber of Spring Perch on Car Chassis

气门弹簧座冷挤压模具结构设计

Design of Cold Extrusion Die for Valve-Spring Base

气缸盖弹簧座孔刀具与沉孔深度尺寸的控制

The Control of Cylinder Cover Spring Holder Hole Cutting tool and Sinks the Hole Depth Size

弹簧座轴承调整螺母

Spring seat bearing adjusting nut

介绍了气门弹簧座的冷挤压工艺和新型模具结构。

The working process for cold extruding of valve-spring base has been described , with a new die structure using ejector turning of itself .

如果已经更换了减震器或松开了弹簧座，拧紧前，将相应的弹簧座与中心对准。

If the vibration damper has been replaced or the spring seat loosened , align the appropriate spring seat in the centre before tightening .

弹簧座由于其螺旋面带来的非对称性，使其冲压成形过程中的受力变形状态要比一般的对称件复杂得多。

Because of its spiral surface which causes asymmetry , the deformation state of spring seat in the stamping process is much more complicated than that of general symmetry part .

针对原弹簧座镦挤模具结构的缺陷，设计了新型镶块式模具结构，使模具成本显著降低。

The weaknesses have been pointed out of former die structure for upsetting and extruding dumb iron . A de-sign of new type of combination die has been presented , resulting in markedly reduced die cost .

上端抵在弹簧座上，在弹簧座的下面用栓销（或叫做定位销）加以定位。定位销定位精度设计的理论概率原理与方法

" The upper end rests against a flat washer , or spring retainer , which is attached to the valve stem by a retainer lock ( also called a keeper ) . " Theoretical Probabilistic Principle and Method for the Orientation Precision Design of Pin

椎环、弹簧、弹簧座以及卡环，辅助密封圈有“O”形橡胶圈和PTFE楔形环，静环材料都为石墨（M106K）。

Vertebral ring , spring , spring seat and clasp , auxiliary seals have " O " shaped rubber ring and PTFE wedge ring , quiet ring for graphite materials ( M106K ) .

阀的水路转换机构由推杆、弹簧、弹簧座、阀门塞等组成。

The water path switching mechanism of the valve is composed of a push rod , a spring , a spring seat , a valve plug , etc.

这三套机械密封都由如下部件组成：动环、静环、推环、弹簧、弹簧座、辅助密封圈、卡环等。

The three sets of mechanical seal components are as follows : actin ring , quiet ring , push the ring , spring , spring seat , auxiliary ring , ring , such as cards .

螺旋弹簧悬架上弹簧座的垫片丢失，也会引起弹簧变软和下垂。

Loss of the shim from the coil spring seat on the coil-spring suspension will cause the spring to seem shorter and to sag .

本文以变刚度气门弹簧为研究对象，建立了气门弹簧、弹簧座的三维有限元组合模型。

In this paper , 3D finite element analytical models of the valve spring and the valve-spring retainer are established for analysis of a variable stiffness valve spring .