导程

波动载荷下扭轮摩擦传动机构的导程分析

Lead analysis of twist-roller frictional transmission structure under dynamic load

本文探讨了正圆柱螺旋面的展开方法及其对实际导程的影响。

Method is approached for expanding cylindrical spiral surface and its effect on actual lead .

方法以图形翻转VEP作为研究工具研究18例正常人30°以外的上方、下方、鼻侧、颞侧4个方向周边区与中央区在Oz导程对比的图形VEP的波形特征。

Methods We use pattern reversal VEP to study wave character of comparing center with periphery in 18 normal adult of outside 30 ° in above 、 below 、 nose and temporal visual field .

另外还用Fluent软件分别对双头不同导程的2种旋转喷头在40MPa进口压力条件下的喷射状态进行分析，从而得出旋转锥形喷嘴的最佳工作状态。

On the other hand , simulate by the Fluent software the jetting status of the double orbits water jet spiral nozzle jetting under 40 MPa pressure-inlet , then got the best working status of the spiral cone jet nozzle .

大导程滚珠丝杠副螺母成型磨削加工建模与仿真

Modeling and Simulation of Large Pitch Ball Screw Nut Formation Grinding

正常成年猫多导程视觉诱发电位研究

A study of the multi-channel visual evoked potentials in adult cats

关于钻尖的变导程拟螺面磨法的研究

A study on grinding method about drill tip with variable-pitch quasi-helicoid

在普通铣床上加工等导程圆锥螺旋线

Processing of equivalent lead conic spiral by using normal milling machine

在普通车床上加工双导程渐厚蜗杆的新方法

The Advanced Process Method of Double Pitch Worm in Engine Lathe

大导程滚珠丝杠副螺母加工中砂轮截形理论分析

Wheel 's Section Theory Analysis of Large Pitch Ball Screw Nut

渐变导程锥形螺杆的数控加工原理与建模

The Machining Principle and Modeling of Conical Screw with Continuous Grading Lead

大导程三头矩形螺纹螺母的数控加工

NC machining nut with large lead and 3-start rectangular thread

滚珠丝杠副导程误差仿动态测量的研究

Research on Simulating Dynamic Measurement for the Error of Ball Lead Screw

用数控车床加工精密螺纹时，在开始段和结束段会出现导程误差。

Lead error would be occurred during process thread by NC lathe .

GB/T17587.2-1998滚珠丝杠副第2部分：公称直径和公称导程公制系列

Ball screws Part 2 : Nominal diameters and nominal leads Metric series

半导程螺旋泵转子加工工艺分析及夹具

Machining technology analysis and clamping apparatus design of helix half-lead pump 's rotor

北回归线和南回归线滚珠丝杆副导程误差的微型机在线回归分析与频谱分析

Microcomputer-Based On-line Regression Analysis and Power Spectrum Analysis of Ball Screw Travel Deviation

大型滚齿机刀架双导程蜗轮副的改装

Retrofit double lead worm gear drive toolpost of heavy duty gear hobbing machine

变倾角变导程螺旋槽的数学建模和加工方法

Mathematic Modeling and Machining Method of Changed Angle and Variable Pitch Spiral Groove

变导程螺旋包络运动分析

The Analysis of Screw Envelop Motion with Variable Pitch

空气锤锤杆导程法兰的修复

Repair on flange of air hammer piston guide bushing

锤杆导程及导板拉伤的修补工艺

Mending of Pulling Damage of Handle of Air Hammer

大直径大导程多头梯形螺纹数控编程研究

Numerical control programming research of the large diameter and steep-lead multiple-trapeziform screw thread

变导程螺旋的数学模型及其计算机辅助设计

Mathematics model of spiral of lead of alteration and its computer supplementary design

用西门子数控立车加工大导程多头螺纹数控编程

The numerical control programming method of steep-lead multiple-thread screw of Siemens NC system

转子导程的参数选择铁磁谐振过电压的计算机辅助分析

Lead Selection for Rotor 's Design The Computer Aided Analysis for the Ferroresonant Overvoltage

分析了转子螺旋角和导程对螺杆压缩机性能的影响，研究了环境温度对压缩机性能的影响。

Effect of spiral angle and rotor lead of compressor on performance is researched .

滚珠丝杠导程误差频谱分析中的几个问题

Problems in Spectral Analysis of Ball-Screw Travel Error

变导程螺旋引纬机构的研究

On the Variable-Pitch Screw Driving of Weft-insertion Mechanism

麻花钻刃磨新方法&变导程螺旋面刃磨法

A New Method of Sharpening Twist Drills