受力分析

计量泵N轴受力分析及结构设计

The force analysis and structure design on N shaft of metering pump

GPS卫星受力分析与轨道确定

Force Analysis and Orbit Determination of GPS

链斗式提升机O形环与U形环受力分析及对比

Mechanical Analysis and Contrast of O-chain Iron and U-chain Iron on Bucket Chain Conveyer

机器人用RV传动中摆线轮受力分析

Force Analysis on Cycloidal Gear of the RV Drive Used in Robot

通过使用UG三维建模软件建立了机械臂的三维模型，为各部件工作时的受力分析和动力学分析打下了基础。

By using UG 3d modeling software , the mechanical arms are established for all parts of 3d model .

CAESARⅡ软件在离心压缩机配管受力分析的应用

Application of CAESAR ⅱ in Centrifugal Compressor

通过H型钢轧件在万能孔型中的受力分析，直接推导出轧件对轧辊的前滑公式。

On the basis of analysing the forces acted on H-beam in rolling by the universal pass , the formulas of the forward slip are derived in this paper directly .

本文开发了一个教育软件&基于WEB的工程力学动态可控受力分析系统。该系统主要用于工程力学课程受力分析部分的计算机辅助教学。

The main job of this thesis is to complete the design of educational software , active and controllable system of force analysis basing on Web , which will be used to assist teaching by computer .

24m跨度承托四层框架的预应力钢筋混凝土梁的设计特点和受力分析

Design Characteristic and Bearing Capacity Analysis of Reinforced Concrete Frame Bearer Girder

并在受力分析的基础上，建立了PDC钻头受力计算模型。

According to the force-balance principle , the mechanical models are developed for calculating all forces exerted on a PDC bit .

介绍了空间三维桁架结构受力分析的有限元方法，运用matlab强大的数学计算功能，解决刚度矩阵的组集和约束条件的处理等问题，编制了通用的求解程序。

The finite element method of 3D space truss force analysis is introduced . The program settles the problems how to assemble the stiffness matrix and how to disposal the constrain based on matlab language .

本文分析了RV传动的原理、特点、效率及结构，较深入地研究了RV传动在运转的不同位置的受力分析。

Analyzes the principle , the characteristics , the efficiency and the structure of RV transmission , studies the force analysis at different positions of RV transmission .

在V形结构的基础上，通过简化力学模型的受力分析，建立力与变形之间的关系，从而获得W形结构的弹性变形公式。

On the basis of V structure , through analyzing the press from the model of mechanics predigested , a relation between strength and transmutation was set up , and the formula of elasticity transmutation of W structure was obtained .

第三，采用ANSYS有限元分析软件分别建立平压试验模型、铺装结构模型和对比模型，对铺装结构进行了系统全面的受力分析。

Thirdly , the paper applies finite element analysis software ANSYS to respectively establish the flat crush test model , the pavement structure model and the contrast model , carrying out systematical and comprehensive stress analysis for the pavement structure .

根据离心球控制的金属带式无级变速器的结构模型和受力分析，建立了CVT的仿真模型，用该模型模拟了无级变速器的速比特性。

According to the metal belt type centrifugal ball control step-less transmission structure model and stress analysis , the simulation model was established , using the model to simulate the characteristics of continuously variable transmission ratio , and verify that the model is correct and feasible .

采用Newton-Euler方法对地震模拟器各部分进行了受力分析，建立动力学模型的开式方程，得到广义输出力解耦的机构结构参数所满足的条件。

The force analysis of every parts of an earthquake simulator is studied by using Newton-Euler method . The dynamics model is derived and the mechanical and structural parameters of meeting the requirement of general decoupled output forces are obtained .

介绍OCS二维速度防护的概念，并分析了它的原理，包括列车在紧急制动和滑行时的受力分析、距离&限速值计算以及允许速度带的计算等。

The paper introduces the conception of 2 D speed protection and analyses its principle , which includes the analyzes of the force on the train when applying the eddy current brake and during the slide , and calculates the distance speed limit curves and the allowable speed range .

纹胸构成部件特征和受力分析

Analysis on the Components Characteristics and Wear - stress of Brassiere

新型液压马达配流盘的受力分析与计算

Mechanical Analysis and Calculation of New-style Distribution Valves in Hydraulic Motors

冲模切管的受力分析及刀片设计

Mechanical Analysis of the Pipe Punch Cutting and the Punch Design

圆环隙口模中聚合物熔体的受力分析

An Analysis of the Stress of Molten Polymers in Annular Dies

钻机液压卡盘的受力分析与计算

Loaded force analysis and calculation on core drill 's hydraulic chuck

隧道混凝土衬砌施工中衬砌台车受力分析

Loading analysis of Lining Jumbo during construction of concrete tunnel lining

大跨越六联耐张绝缘子串受力分析研究

Forced Analysis of Tension Six String Insulator Assembly in Long Span

明挖结构使用阶段的受力分析

Stress Analysis of the Structures Built by Opencut Method during Operation

推杆齿条传动的受力分析与啮合效率解算

Analysis of Force and Meshing Efficiency of Push Rod Rack Drive

本文采用有限分段变换法对斜交薄壁箱梁进行了空间受力分析。

A finite segmental transformation method is presented in this paper .

炮弹头螺受力分析及联接方式改进

Strength analysis on head of shell and improvement on joint form

间隙销支座单层球面网壳的支座体系受力分析

Behavior of clearance-pin support system in a single-layer spherical lattice shell

框架木箱的结构及受力分析

Analysis on The Structure and Loading of the Framed Wooden Case