分子筛吸附器

60000m~3/h空分设备分子筛吸附器的开发与设计

Development and design of a molecular sieve adsorber for 60000m ~ 3 / h air separation unit

分子筛吸附器自动再生系统在DCS中实现

Realization of Molecular Sieve Adsorber Automatic Regeneration System in DCS

用PLC实现空分分子筛吸附器切换控制系统的改造

Modification of the Switching Control System for Molecular Sieve Absorber by PLC

加温KL-15型制氧制氮车分子筛吸附器应注意的问题

Some problems needing attention in heating MS adsorbers of model KL-15 oxygen / nitrogen production trucks

分子筛吸附器进水故障的分析与处理

Fault analysis of carrying water into MS adsorbers and solutions

分子筛吸附器进水故障及其处理过程

Water intrusion into molecular sieve adsorber and its remedying treatment

分子筛吸附器两起故障的原因及处理

Cause and treatment of two malfunctions in molecular sieve adsorber

分子筛吸附器的自动切换控制系统

An automatic switching control system for molecular sieve adsorbers

分子筛吸附器带水故障的分析及处理

Analysis and treatment of molecular sieve adsorber water-flooding malfunction

采用床层探位法解决分子筛吸附器空气偏流问题

Bed - layer probing for solving air deviation problem in a molecular sieve adsorber

空分设备启动前分子筛吸附器和空分塔进水的处理

Treatment of water-flooding accident in molecular sieve adsorber and air separation column before startup

分子筛吸附器出口空气中二氧化碳含量严重超标的分析与处理

Analysis and treatment of the severely over-standard carbon dioxide content at the outlet of molecular sieve adsorber

最后得出了发现及处理分子筛吸附器进水故障的经验和教训。

The experience and lesson about checking and treating the malfunction of water intrusion into molecular sieve adsorber are also summarized .

空分设备启动前的加温阶段，分子筛吸附器和空分塔上、下塔大量进水。

A mass of water entered molecular sieve adsorber , upper column and lower column during the heating period before startup of air separation unit .

以小型空分设备分子筛吸附器的孔板分布器为例，通过例题演算，介绍了设计程序。

The design program has been introduced with a perforated plate distributor in a molecular sieve adsorber of a small scale air separation unit as an example .

并介绍了正确的加温方法，分子筛吸附器出口空气温度变化曲线和加温中需注意的其它问题。

The correct heating methods and the curve of air temperature change at outlets of MS adsorbers and the other problems needing attention in heating operation are described .

针对加温KL15型制氧制氮车分子筛吸附器过程中易出现的问题，提出了应采取的相应措施；

The relative measures to be taken are put forth corresponding to the problems liable to happen when heating MS adsorbers of model KL 15 oxygen / nitrogen production trucks .

介绍因空冷塔结垢水被带入6000m3/h空分设备分子筛吸附器的故障现象、原因分析及处理措施；

The fault phenomena of carrying water into MS adsorbers of 6000m 3 / h air separation plant caused by scale deposited in air cooling towers , cause analysis and solutions are described .

由于分子筛吸附器筛网格栅与支撑环板连接处存有裂缝，使氧化铝颗粒泄漏到出口，并从污氮放空消声器处吹出；

The alumina granules leak to the outlet of molecular sieve adsorber and escape from exhaust silencer of waste nitrogen , due to the crack at the joint between sieve spacing grid and supporting ringy plate .

对分子筛吸附器在一个运行周期不同阶段的温度曲线的特有形状形成原因进行技术分析及总结，给出温度曲线发生各种异常变化时，判断生产中存在问题的方法及相应的处理措施。

Analyzes reasons for the formation of the specific temperature curve of molecular sieve adsorber at different stages of an operating period , and presents methods to judge the problems existing and corresponding solutions when there are abnormals in temperature curve during production .