冲天炉

冲天炉炉缸用Al2O3-SiC-C质捣打料的研制

Development of Al_2O_3-SiC-C ramming mix bonded by phenolic resin for hearth of cupola furnace

本文叙述了用MgTiCaReSiFe单一合金作蠕化剂，用冲天炉铁水制造纺织机齿轮的试验研究工作。

Using Mg-Ti-Ca-Re-Si-Fe single alloy as a modifying agent , the experimental work for producing compacted graphite cast iron gears with cupola melting iron is described .

介绍了用微机和可编程序控制器（PLC）组成两级分布式冲天炉自动加料控制系统的设计及实现方法。

Two stage distributed control system using PC and PLC is illustrated .

用Java语言基于线性规划的理论开发了一个冲天炉的最低成本配料系统，并且采用B/S模式实现。

The least-cost cupola furnace system based on linear programming has been developed by using Java and we can use the system which be built in B / S module .

多程管式烟囱高温热风冲天炉GL型高温热风炉的开发研究

Hot-blast Cupola of multipass exchanger in chimney Study on GL Style High Temperature Hot-blast Stove

10t冲天炉最佳结构及工艺的确定

Deciding for Optimal Structure and Process Parameter of 10 t Blast Furnace

SG对薄壁蠕墨铸铁件蠕化范围的影响用冲天炉生产蠕墨铸铁件的试验

The Effect of SG on the Compacted Range of Graphite in Thin Section Castings of C / V Cast Iron

在7t／h冲天炉上设计、制造、安装了喷吹焦（煤）粉装置，并进行了冲天炉喷煤粉试验。

A coke / coal pulverization and injection unit was designed and installed on a 7 t / h cupola .

冲天炉操作中要采取适当措施，使炉渣中的FeO含量不超过5%。

Some proper measures must be adopted in cupola melting operation to keep the FeO content less than 5 % .

在冲天炉熔炼条件下，研制了Cu、Cr铸态球铁曲轴，并进行了铸态和正火球铁曲轴的实体疲劳对比试验。

Under practical cupola melting condition have been produced Cu , Cr alloyed ductile iron . The realistic fatigue behavior of the as-cast ductile iron crankshafts has been compared to that of normalized ductile iron crankshafts .

介绍冲天炉除尘洗涤循环水处理工艺过程，包括絮凝沉淀、SO2的吸收、循环水冷却、水质稳定、污泥脱水等过程。

The article introduces the treatment process of circulating water dedusting from blast furnace , including flocculating precipitation , SO 2 absorbing , cooling circulating water , stability water quality , sludge desiccation etc.

通过对10t/h冲天炉的改造，将3排小风口冲天炉改为两排大间距结构，用正交设计法试验确定10t冲天炉最佳结构及工艺参数。

The orthogonal method is adopted to decide the best structure and process parameters at the condition that two rows large space structures of 10 t / h blast-furnace was reformed .

论述了“KQDL系列冲天炉”采用空气冷却、强化预热、单排龙卷风供风原理和特点。

The principle and characteristics of KQDL series cupola which supply blast using air cooling , strengthening preheating and single row cyclone were discussed .

运用冲天炉熔炼试制QT400-18球墨铸铁，作为锌锭模的材质，提高锌锭模使用寿命。

To use pick cupola smelting triM-produced QT400-18 ductile iron , zinc ingots module as material , improve zinc ingots mode using life .

前言：针对冲天炉，冷风炉、热风炉、水冷却炉存在的问题试制出了“KQDL系列冲天炉”。

The KQDL series cupola was trial produced aiming at the problems existing in the cupola , cold blast cupola , hot blast cupola , water cooling cupola .

优化设计在冲天炉配料中的应用

Application of Optimizing Design Idea to Charge Calculation of Cupola Melting

冲天炉多功能自动巡回检测显示仪的研制

Development of the Multifunctional Apparatus of Automatical Roving Examination for Cupola

冲天炉熔炼过程控制方法的研究

Investigation on the Control System of the Melting Process in Cupola

连续出铁出渣冲天炉故障时的防护方法

Failure Protection Measures for Continuous Metal - Tapping and Slagging Cupola

在冲天炉中熔炼铁精矿粉的试验分析

Experimental Analysis of the Iron Ore Concentrates Melting in the Cupola

在冲天炉上生产高碳当量高强度薄壁铸件的探讨

Production of High-strength Gray Iron Castings With High-carbon Equivalent n Cupola

冲天炉熔炼过程参数变化及其检测方法

The Parameter Changes and Its Measuring in Melting Process of Cupola

这种装置在小型冲天炉中是作为砂粒分离器使用的。

These units are employed as grit arrester on small cupola .

5吨/时冲天炉风量微机控制

Microcomputer Controlling on Blast Volume in a 5t / h Cupola

冲天炉微机自动加料的精度分析与实践

The Accuracy Analysis and Practice of Self-motion Charging Process of Cupola

高铬刚玉在冲天炉上的应用

Application of Corundum with High Cr_2O_3 Content to the Cupola Furnaces

介绍了冲天炉加料自动控制系统。

The automatic control system of the cupola feeding is introduced .

拥有冲天炉、电炉、行车等设备。

Cupola owned , electric furnace , traffic and other equipment .

两排大间距结构在10t/h冷风冲天炉上的应用效果

Application of the Best Structure in 10 t / h Blast-furnace

冲天炉新技术（4）：天然气冲天炉

New Technology in the Cupola ( Part ⅳ) Natural Gas Cupola