乳液稳定性

研究了磺化油SS的乳液稳定性、乳化能力以及在制革中的应用，并与氧化亚硫酸化菜油进行比较。

The stability of emulsion , the emulsifying ability of sulphonated oil SS and the application in the leather-making are studied .

当连续相中电解质浓度增加时，乳液稳定性下降，且Na2CO3比NaCl的作用强。

The stability decreased when electrolyte concentration was high , and Na2CO3 was stronger than NaCl .

本文首次研究了盐浓度对W／O乳液稳定性的影响。

Here , the effect of salt concentration on the W / O emulsions stabilized by organoclay was studied .

同时研究了GO浓度、连续相的pH值以及水油比对Pickering乳液稳定性及其液滴尺寸的影响。

Also we studied the impact to the stability and the size of the droplet of the concentration of GO , pH , ratio of oil-water .

当HAM用量较大时，乳胶粒间亦发生团聚，乳液稳定性下降。

Aggregation tends to take place among particles as the increase of HAM dosage , resulting in the decrease of emulsion stability .

讨论了原料NCO/OH值、反应温度与时间、扩链剂用量、溶剂用量对乳液稳定性的影响，并用TEM和FT-IR对乳液进行了结构表征。

The effects of NCO / OH ratio , reaction temperature , chain expand and solvent on the emulsion stability were discussed in detail .

对影响丙烯酰胺（AM）&丙烯酸（AA）单体反相乳液稳定性的各种因素进行了较全面的探讨，找到了较为合适的乳化体系及其乳化条件。

The factors effecting the stability of AM-AA monomer inverse emulsion were investigated . A suitable emulsifying system and its emulsifying conditions were found .

CTAB/丁醇/庚烷/水四组分微乳液稳定性研究及BaF2纳米粉体制备

Stability and Synthesis of Barium Fluoride Nanoparticles from CTAB / Butanol / Heptane / Water Microemulsion System

考察了GO与传统乳化剂十二烷基苯磺酸钠（SDBS）对乳液稳定性及其液滴尺寸的影响。

And we studied the influence to the stability and the droplet size of the GO sheet in contrast to the traditional emulsifier sodium dodecyl benzene sulfonate ( SDBS ) .

通过红外光谱分析了水性PU树脂的结构组成：透射电镜（TEM）研究了乳胶粒子尺寸与乳液稳定性的关系；

The structure of waterborne PU emulsion is analyzed by IR ; relationship between the particle size of emulsion and stability was studied by transmission electron microscopy ( TEM );

研究了有机硅氧烷单体的种类、用量和添加方式以及水解抑制剂用量、体系的pH值、复合乳化剂的配比对自交联型有机硅氧烷改性丙烯酸乳液稳定性的影响并揭示其规律。

The effect of species , level and procedure of adding organic siloxane , content of hydrolyzation inhibiter , pH value and partition of composite emulsifier between nucleus and shell on the stability of acrylate emulsion was studied .

研究结果表明：加入作为可聚合乳化剂的AMPS减少了常规乳化剂的用量，并能维持很高的乳液稳定性。

Testing results showed that reactive surfactant AMPS could reduce the content of traditional emulsifier , and could maintain high stability of latex .

结果表明：在制备PS微球时，引发剂用量、离子强度、助溶剂种类及用量等均对乳胶粒和乳液稳定性有影响。

It was found that in the preparation of PS microspheres ; the initiator concentration , ionic strength , the type and amount of latent solvent can affect the latex particles and emulsion stability .

研究了工艺条件、DMPA用量和乙二胺（EDA）用量对乳液稳定性及涂膜硬度、附着力和吸水率的影响。

The effects of reaction conditions , DMPA content and EDA content on emulsion stability , hardness , adhesion and water absorption of the coating film were discussed .

并选用三种表面活性剂为两性淀粉、PVA、KIA-96来改善水性环氧树脂乳液稳定性。

Ultimately we select these three kinds of surfactants amphoteric starch , PVA , KIA-96 to improve the stability of waterborne epoxy resin emulsion .

讨论了温度、时间、转速和表面活性剂的用量等对乳液稳定性和粒径的影响，确定了乳化的最佳条件：50℃、15min、转速为900r/min、表面活性剂为4%；

The optimal emulsifying conditions are as follows : temperature is 50 ℃; time is 15min ; rotation speed is 900r / min and surfactant dosage is 4 % .

简述了乳化剂对乳液稳定性的作用，实验数据表明，制备水包油（O/W）型水乳化硝基木器漆乳液时的最适宜HLB值范围为13.1～13.2。

The effects of emulsifier on the stability of emulsion were briefly described . The experimental data show that optimal value range of the HLB in preparation of O / W title coating is 13.1 ~ 13.2 .

研究了HTPB与PPG相对含量变化对乳液稳定性、固化膜的耐水和耐乙醇性、热稳定性、软硬段相容性以及力学性能的影响。

Effects of relative content of HTPB and PPG on emulsion stability , resistance to water and ethanol , thermal stability , compatibility of soft and hard segment as well as mechanic property of cured film were investigated .

考察了八甲基环四硅氧烷（D4）在碱性条件下的温度、pH值、反应时间以及乳化剂复配和用量、偶联剂用量等影响单体转化率、乳液稳定性及聚合物分子量的因素。

The influence of factor octamethylcyclotetrasiloxane ( D_4 ) on the monomer convert ratio , emulsion stability and the polymer molecular weight in the alkalescence condition , such as temperature , pH , reaction time and dosage of emulsifying agent and silane coupling agent were studied .

研究了PTMG/PU中软硬段比例、溶剂、软段相对分子质量、扩链剂用量、AKD含量对乳液稳定性和施胶性的影响。

The proportion of soft and hard segment in PTMG / PU , solvent , soft segment molecular weight , dosage of expanding - chain agent and influence of AKD content to emulsion stability and sizability were studied .

结果表明，两性乳化剂MS1具有较高聚合速度，同时具有较好的乳液稳定性，在聚合后的乳液中加入Op10，可提高胶乳的化学机械稳定性。

Results show emulsifier MS 1 , an amphoteric surfactant , providing relatively high polymerization rate with good latex stability . The addition of Op 10 after polymerization reaction will increase stability .

当HEMA用量为4%时，乳液稳定性好，胶膜的耐水性和热稳定性优于核壳未交联，BOPP/铝箔的180°剥离强度最好（值为0.263kN·m-1）。

When HEMA contents was 4 % , emulsion stability was better , the water resistance and thermal property of film were superior to the uncrosslinking , 180 ° peel strength of BOPP with aluminum was best ( numerical value was 0.263 kN · m-1 ) .

利用自乳化技术合成了贮存稳定的聚氨酯水分散体，探讨了影响TDI-N330反应体系中乳液稳定性及成膜物表面结构的各种因素，并用红外与扫描电镜进行了表征。

Probed into the different factors for the effect of emulsion stability and the surface structure of film forming substance in the TDI-N330 reaction system , and token by using infrared ray and SEM .

有机硅阴离子氨基乳液稳定性探讨

A study on the stability of amino silicone anionic emulsion

碱/表面活性剂/聚合物对乳液稳定性的影响

Effects of Alkali / Surfactant / Polymer on Stability of the Emulsion

助乳化剂对化妆品乳液稳定性和液晶性的影响

Influence of co-emulsifier on stability and liquid crystal status of cosmetic emulsion

讨论了消泡效果，乳液稳定性和制备工艺。

The defoam effect 、 emulsion stability and technological process were discussed .

制备工艺对硅/丙复合乳液稳定性的影响

Effect of Preparing Technology on Stability of Polysiloxane / acrylate Composite Emulsion

探讨了影响这一乳液稳定性的因素。

The factors affecting stability of the emulsion were discussed .

关于影响硝酸纤维素光亮剂乳液稳定性的因素探讨

Investigations Into Factors Affecting Stability of Nitrocellulose Topcoat Emulsion