热挤压

热挤压对SiCW/Al复合材料塑性的影响

Influence of Hot Extrusion on the Plasticity of SiC_W / Al Composites

挤压铸造SiCw/L3复合材料的热挤压

Hot Extrusion of Squeeze-cast SiC_w / L3 Composites

热挤压和时效处理对SiCw/LD2复合材料拉伸性能的影响

Influence of Hot-extrusion and Ageing Treatment on Properties of SiCw / LD2 Composites

基于ANSYS的三维建模方法与热挤压模具的优化设计

Method of three dimensional model and optimum design of hot extrusion mould based on ANSYS

喷射沉积SiCp/Al复合材料及6066铝合金热挤压工艺的研究

Study on the Extrusion Process of Spray-Deposition SiC_p / Al Composite and 6066 Al Alloy

基于ANSYS的多边形铝型材热挤压模的三维建模技术研究

Study on the Methods of 3D Molding of Polygon Aluminum Profile Hot Extrusion Die Based on ANSYS

Al2O（3p）/LY12复合材料热挤压材的组织与力学性能

Microstructure and Mechanical Properties of Extruded A1_2O_ ( 3p ) / LY12 Composite

CAE技术在汽车半轴套热挤压缩管成形中的应用

Application of CAE Technology in Forming of Hot-extruding Compressed Pipe of Half-axile Bush

确定了Al-Si复合材料压力熔渗和热挤压工艺参数；

The processing parameters of pressure infiltration and hot extrusion were confirmed .

热挤压变形对Al-Si复合材料组织性能的影响

Effect of Hot Extrusion Deformation on Microstructure and Mechanical Properties of Al-Si Composite

采用拉伸力学性能测试和金相分析，研究了Ag合金化对热挤压前后耐热AlCuMg合金组织与性能的影响。

The effect of metalized Ag on microstructure and properties of heat resistant Al-Cu-Mg alloy are investigated by tensile test and metallographic analysis .

粉末316L不锈钢热挤压工艺

On Hot Extrusion Process of P / M 316L Stainless Steel

（Ce-TZP）-Al2O3陶瓷热挤压模的研制

Study of ( Ce-TZP ) - Al_2O_3 Ceramic Hot Extrusion Die

SiCw/Al复合材料热挤压模具设计及其对挤压棒材组织和性能的影响

Design of Dies for Hot Extruded SiC w / Al Composites and Its Effect on the Microstructure and Properties of Extruded Rods

热挤压变形对亚微米Al2O（3p）/Al复合材料组织性能的影响

Effect of hot extrusion deformation on microstructure and mechanical properties of sub-micro Al_2O_ ( 3p ) / Al composite

研制了（Ce-TZP）-Al2O3陶瓷热挤压模具并进行了工业应用试验。

( Ce-TZP ) - Al2O3 ceramic hot extrusion die was studied .

本文采用机械合金化（MA）与真空热压烧结（HP）的方法制备了Al-Pb合金，并进行了热挤压变形处理。

The Al-Pb alloy was fabricated by mechanical alloying and vacuum hot-pressed sintering and hot extrusion .

基于Taguchi的轮毂套管热挤压工艺优化

Optimization of the Hot Extrusion Parameter for Hub Tube Based on Taguchi Method

W-Cu粉末热挤压致密工艺及塑性变形研究

Research on Densification of W-Cu Powders by Hot Extrusion and Plastic Deformation

粉末热挤压Al-Zn-Mg-Cu系合金的热处理工艺

Heat treatment process of Al-Zn-Mg-Cu alloy fabricated by powder hot extrusion technology

热挤压原位合成TiB2/6351Al复合材料的组织性能

The microstructure and properties of in-situ TiB_2 / 6351 Al composites after hot extrusion

Ag合金化对热挤压前后耐热Al-Cu-Mg合金组织和性能的影响

Effect of Metalized Ag on Microstructure and Properties of Heat Resistant Al-Cu-Mg Alloy Before and After Hot Extrusion

分析了压力熔渗和热挤压工艺对Al-Si复合材料成形性、组织和性能的影响；

The influences of the processing parameters on the formability , the microstructure and the properties of Al-Si composites were discussed .

利用ANSYS软件，对某型行波管TWT慢波部分的装配热挤压装置，进行热-结构耦合分析。

The coupling thermal-structure of the assembled thermal-squeezing device in TWT slow wave part of some type is analyzed by utilizing ANSYS software .

利用化学共沉淀法及高能球磨工艺制备微米级Ag包覆SnO2复合粉末，然后采用冷等静压和烧结热挤压法制备AgSnO2材料。

AgSnO_2 contact material is developed by chemical co-precipitation , high energy ball milling and powder sintering as well as hot extrusion .

该方法以有限元分析软件ANSYS为开发平台，已成功地应用于建立铝型材热挤压平面分流组合模的实体模型，从而为进一步进行有限元分析和优化设计奠定了基础。

The " skinning " method , which is based on finite element analysis software-ANSYS , is successfully used in building the model of aluminum profile hot extrusion porthole compound die .

铸造H13模具钢在热挤压模中的应用

Application of Cast Dies Steel H1 in Thermal Extruding Die

方法选择1997~2004年肢体三度烧伤患者157例作为A组，1991~1996年肢体三度烧伤患者80例作为B组，排外电烧伤、热挤压伤等深三度烧伤。

Methods Except electric burn and hot extrusion injury , 157 patients from 1997 to 2004 year and 40 patients from 1991 to 1996 with full thickness limbs burn in our department were selected as group A and B respectively .

开展了SiC颗粒增强铝基复合材料热挤压工艺的实验研究，分析了其挤压成形的力能变化规律。

The hot extrusion process of the aluminium alloy matrix composite reinforced by SiC particles was researched by experiments , the law of the energy change during the forming process was analysed .

结果表明，磨损表面形成一层含有Al、Si、Pb、O化合物组成的反应膜，可显著地改善热挤压铸造合金的抗咬合性能；

Results indicates that a friction reactive film composed of Al , Si , Pb , O compounds and formed on the worn surface can effectively improves the anti-seizure property of hot extruded casting alloy .