间隙配合

  • 网络Clearance fit
间隙配合间隙配合
  1. 在转子压缩机内转子和气缸之间采用间隙配合,其泄漏通道通过油膜来密封的。

    In rolling piston compressors , clearance fit is adopted between rotor and cylinder . Its leakage passages are pressurized by oil films .

  2. 所述编程按钮(1)位于按钮孔(2)中,并与按钮孔(2)间隙配合;

    The programming button ( 1 ) is positioned in the button hole ( 2 ), and is in clearance fit with the button hole ( 2 );

  3. 在采用特征线破坏假设和Yamada-Sun准则,对多钉连接进行强度计算后,结果表明,采用适量干涉和间隙配合方法,可使多钉连接载荷分配趋于均匀,从而提高连接强度。

    Also by introducing the characteristic curve hypothesis method and the Yamada-Sun failure criterion , the strength , which use suitable clearance and interference in each hole , can improve obviously .

  4. 研究结果表明:复合材料干涉配合接头的疲劳寿命远远高于间隙配合接头的疲劳寿命;

    The fatigue life of interference-fit composite joint is affected highly by interference quantity ;

  5. 该蜗轮箱由蜗轮套及油缸两部分组成,油缸小间隙配合装配在缸套内,并用密封圈密封防漏。

    The hydro-cylinder is installed in the cylinder casing with small fitting clearance , which is sealed with a collar seal .

  6. 阀体组件与锅盖内衬轴孔间隙配合,且轴向有一定的浮动距离。

    The valve component matches the gap of the shaft hole of the cooker cover liner and axially has a certain floating distance .

  7. 击锤与机体间隙配合,可在机体内滑动压缩击锤簧储存能量。

    The hummer is coordinated with the gap of body , can slide and contract the energy storage of hammer spring in the body .

  8. 介绍设计过程中选用过渡配合时,应用概率统计理论,精确设计过渡配合中需要出现过盈、间隙配合概率的方法。

    This chapter introduces a way by which interference fit or clearance fit probability needed in transition fit can be exactly designed , when selecting transition fit and applying probability statistic theory .

  9. 采用三维有限元法,利用在大载荷孔上使用间隙配合、在小载荷孔上施加干涉配合的方法,使各钉载荷分配均匀化。

    Also it has , with the method of 3D FEA , through use clearance fit in the higher load hole and interference fit in the lower load hole to proportion load distribution .

  10. 将自由镦粗毛坯外径与冷挤压凹模的关系理解为间隙配合,确定了毛坯的基本偏差和公差带。

    The relation between the outer diameter of free upsetting blank and the inner diameter of cold extrusion die can be comprehended as clearance fit , to confirm the basic tolerance and tolerance band of the blank .

  11. 在滚动转子式压缩机内由于间隙配合造成的制冷剂泄漏中,转子径向间隙的泄漏量最大,它主要是以溶于润滑油的形式泄漏的。

    Among refrigerant leakages are caused by clearance fit in rolling piston compressors , the maximal amount of leakage is occurred in the radial clearance , which is mainly processed by the mode that the refrigerant dissolves into the lubricant .

  12. 110KV变压器中性点过压保护中阀式避雷器和间隙的配合问题及措施探索

    Arresters and rod gaps are used together on over-voltage protection for neutral of 110 kV graded insulated transformers

  13. 电动式同步调整送纸后挡板间隙,配合低阻力滑轨、使送纸平顺。

    Motorized synchronized adjust back damper gap , cooperate with slide rails , ensure feeding board smoothly .

  14. 胶原酶硬膜外前间隙注射配合留管治疗腰椎间盘突出症

    Epidural injection of collagenase from front clearance coordinating block therapy of keeping tube for treatment of lumbar disc herniations

  15. 通过保护间隙与工作间隙放电特性的配合试验,证明加装保护间隙不仅可提高带电作业的安全性,而且能有效地减小塔头尺寸。

    Through the coordination test of discharge characteristics for protective gap and working gap , it is proved that adding protective gap can not only improve the safety for live line work and can reduce the tower size efficiently .