间隙控制

基于PC的光学速调管磁间隙控制系统

The magnetic gap control system of the transverse optical klystron based on PC

基于ISA总线的线切割间隙控制板的设计

Design of Wire cutting Gap control Board Based on ISA Bus

N-90系统在大机组空预器密封间隙控制中的应用

Application of N-90 DCS at AH Sealed Interval Control for Large Unit

热磨浆机的机液伺服间隙控制系统研究

A Research on the Controlled Clearance of a Thermal Pulp Grinding Machine

三组元比例控制器的端面间隙控制及内泄漏分析

Radial clearance control and internal leakage analysis of tri-proportion controller

容克式空气预热器密封间隙控制系统的研究与应用

Research and Application of an Air Preheater Leakage Control System

磁悬浮列车轨道间隙控制系统的自适应控制

Self-adaptive Control of Magnetic Suspension Train Track Gap Control System

某型发动机高压12级转子叶尖间隙控制研究

Research on turbofan engine HP-compressor rotor-12 blade tip clearance control

设计制造中的间隙控制；

Clearance control of the rotors of the screw ;

回转式空气预热器密封间隙控制策略

Clearance control strategy in rotary air - preheater

薄板拉延成形的固定压边间隙控制方式研究

Research on Sheet Metal Forming Under Fixed Blankholder

采用多种先进控制方法改进设计空气预热器密封间隙控制系统

The Reformative Design of Air Preheater Leakage Control System by Several Advanced Control Methods

由于电火花加工电磁干扰强，间隙控制是要求响应速度快。

Because of edm electromagnetic interference is strong , clearance control is to require fast response .

大型火电厂空气预热器间隙控制系统的现场改造与自动投入

Site Retrofitting Auto Putting into Service of Air preheater Clearance Control System in Large scale Thermal Power Plant

试验结果证明轴向间隙控制在0.03～0.08mm是合理的。

Tests prove that it is proper to fix the axial clearance at 0 . 03-0 . 08 mm .

基于不破裂前提，从合理压边间隙控制中获得常压边力控制所需的恒定压边力。

Based on the prerequisite of no cracking , the fit constant BHF was acquired from reasonable blankholder gap control .

简述了航空发动机转子叶尖间隙控制的意义及作用，转子叶尖间隙设计选择的依据。

The importance of controlling aeroengine rotor tip-clearance and the basis of selecting the clearance in design are briefly presented .

最优预见算法构造电火花放电间隙控制专家系统研究

The study of constructing the expert system of control with electro discharge gap on the calculate way of superior foresee controlling

分析了电站空气预热器漏风及产生的原因，介绍了间隙控制系统方案、系统硬件配置及软件设计。

The result and harmfulness by air leak of the air preheat device are analyzed , The hardware and software of the system are introduced .

本文采用了多种先进控制方法，用来改进传统的非接触式空气预热器密封间隙控制系统。

In this thesis , several advanced control methods are adopted to improve the performance of the traditional air preheater leakage control system using non-touched sensor .

阐述最优预见控制算法在构造电火花放电间隙控制专家系统中的应用技术实例。

It is showed the practical examples of which constructs the expert system of control with electro discharge gap in the calculate way of superior foresee controlling .

这些工作对于发动机初步设计设计和叶尖间隙控制理论研究有一定的参考价值。

Research finding about the tip clearance of engine in the paper is basal ; they can be used as reference of aero-engine design and the tip clearance control .

结果表明：应将阀芯和阀体的配合间隙控制在0.007mm以内，节流阀对中误差控制在30%以内；

The results show that the clearance of spool and valve body should be controled within 0 007 mm , error of centralization of throttle valve within 30 % .

针对微细电解加工中阳极溶解定域性问题和微小间隙控制难的特点，本文以电解液为出发点，采用超纯水作为电解液。

In Micro-ECM , it is necessary to solve the problem of localization of anodic dissolution , and hard to control the gap between the electrodes , which is micro scale .

介绍了种子激光扫描聚焦系统、同步系统、光学速调管磁极间隙控制系统、磁场测量系统及辐射测量系统。

And it also gives an introduction to the scanning and focusing system of seed laser , synchronization system , magnetic gap control system , magnetic measurement system and radiation measurement system .

提出一种脉冲均匀调制功率控制串联谐振式DC/AC逆变器，对其开关进行了均匀对称间隙控制。

A novel PSM ( Pulse-Symmetrical Modulated ) power control serial-resonant DC / AC inverter is proposed . The main switches of the inverter are controlled according to the PSM and work in shutting off and switching on at ZCS .

通过飞机导管高温钎焊时Ni-Cu-Mn-Co钎料传热特征的物理模拟，得到了钎焊间隙的控制要素。

By the physics simulation when the solder of Ni-Cu-Mn-Co transferred heat in high-brazing the aeroplane pipes , the factors were attained to control the brazing gap .

平面弹性机构间隙效应控制研究

On the Control of Clearance Effects in the Planar Elastic Mechanism

发动机活塞顶面与缸盖间隙的控制

Controlling the Clearance Between Engine Piston Top and Cylinder Head

机匣喷气位置对涡轮间隙流动控制的影响

Effects of casing air injection position on controlling tip clearance flow in axial turbines