镇静钢

本文简要介绍了国内外低温条件下石油化工设备用铝镇静钢和Ni系低温钢的标准及现状；

This paper introduces the standard and current situation on aluminium killed steel and pre-low-temperature nickel steel for petrochemical equipment in low temperature condition at home and abroad .

Si镇静钢的优点是可以消除水口堵塞，钢的纯净度与Al镇静钢相近。

The advantage of Si killed steel is to be able to eliminate the nozzle clogging and the cleanliness of the Si killed steel is very close to the Al killed steel .

薄板坯连铸连轧流程低碳Al镇静钢组织细化原因探讨

Study on Structure Refinement of Low Carbon Al-killed Strip Produced by TSCR

含Li2O方坯连铸结晶器保护渣在低硅铝镇静钢中的应用

Practice of Li2O-contained mould powder for low silicon Al-killed steel billet

硅镇静钢热浸镀Zn－Ni合金

Hot Dipping Zn-Ni Alloy for Si-Killed Low Carbon steel

CSP流程中B对低碳Al镇静钢组织及力学性能的影响

Effect of B on Microstructure and Mechanical Properties of Carbon Steel Produced by CSP

RH处理低碳铝镇静钢的脱氧工艺优化

Optimization of Deoxidization Process for Low-Carbon Aluminium-Killed Steel Via RH Treatment

LDRHCC工艺生产低碳铝镇静钢清洁度的研究

Research on the cleanliness of low carbon Al-killed steel during LD-RH-CC process

RH处理对低碳铝镇静钢洁净度影响的研究

Effect of RH treatment on low carbon Al-killed steel cleanliness

LF炉冶炼铝镇静钢预防水口结瘤的措施

Countermeasures to Prevent Nozzle Blocking for Aluminum Killed Steel Smelted by Ladle Furnace

转炉RH连铸工艺过程中低碳铝镇静钢的清洁度

Cleanliness of Low Carbon Al-Killed Steel during LD-RH-CC Processing

RH处理超低碳铝镇静钢的总氧预测模型及应用

Total oxygen prediction model of ultra-low carbon aluminum killed steel in RH treatment and its application

邯钢CSP低碳铝镇静钢非金属夹杂物行为研究

Investigation on Non-metallic Inclusions in Low Carbon Al-killed Steel Produced by CSP at Handan Steel

研究了硅镇静钢在Zn－0.09%Ni合金镀液热镀后镀层的组织结构、耐盐雾腐蚀性能，并研究Zn－0.09%Ni合金镀液对锌锅材料的腐蚀作用。

The paper deals with the Microstructure and corrosion performance of Si-Killed Low Carbon Steel after hot-dipped in Zn-0.09 % Ni alloy bath .

转炉ANS连铸工艺生产低碳铝镇静钢洁净度研究

Investigation on cleanness of low carbon aluminium killed steel produced by bof-ans-cc production route

TSCR生产低碳铝镇静钢薄带软化机理研究

Softening Mechanism of Low-Carbon Al-Killed Steel Strip Produced by TSCR Route

应用美国雷克公司TN－314氮测定仪步进升温的特性，测定了低碳铝镇静钢中氮化铝所含的氮。

Nitrogen content in the aluminum nitride of low carbon Al Killed steel was measured using U.S.TN-314 nitrogen measurement meter with a feature of stepping-up temperature rise .

对于含碳量0059%的低碳铝镇静钢，获得最大r值的冷轧压下率为73%，而Δr值随冷轧压下率的提高单调减小。

For the low carbon Al-killed steel with 0.059 % carbon , the maximum - value is achieved at the reduction ratio of 73 % and Δ r - value is monotonously reduced with the increment of cold rolling reduction ratio .

一些Al镇静钢在优化钢包渣成分和控制FeSi中Al和Ca含量的条件下有被Si镇静钢取代的趋势。

A universally acknowledged trend is that the Al killed steel is gradually replaced by Si killed steel although the Al killed steel is believed to be able to optimize the slag compositions in ladle and control Al and Si contents in the Fe Si alloy .

根据大量的生产研究，认为半镇静钢随着[Si]含量的提高，钢坯切头率增加，B5b半镇静钢的适宜硅含量，应控制在0.07%以下。

According to studies carried out in the plant , the percentage of bloom-crop end increased with an increase of Si content . The Si content of semi-killed steel B , b should be controlled below 0.07 % .

研究了B元素对CSP流程生产的低碳Al镇静钢热轧钢带的组织及力学性能的影响，探讨了B元素在CSP流程中的析出规律及对AlN和MnS析出行为的影响。

The effect of B on microstructure and mechanical properties of low carbon steel produced by compact strip production ( CSP ) was studied . Precipitation behavior of B and the effect of B on precipitation of AlN and MnS are discussed .

通过对半镇静钢气瓶用热轧钢板的三维取向分布函数（ODF）的测试与其反极图的分析，研究厂终轧温度和终轧道次变形量对HP255b热轧板织构和深冲性能的影响。

The effect of the finishing temperature and finishing pass reduction on the texture and drawability of hof rolled plate of semi-killed steel is studied with an analysis of ODF and inverse pole figure .

为了消除TiSULCAK（含Ti超低碳铝脱氧镇静钢）钢冷轧薄板上的铅笔型气泡，将铸机从弧型改为立弯型是最有效的措施；

Conversion of caster from the curved to the vertical bending one is the most effective measures to eliminate the pipe listers and slivers for cold rolled Ti SULCAK ( Ti-beating extra low carbon steel sheet ) .

通过试验分析了不同的光整工艺对热镀锌板屈服强度、n值和表面质量的影响，由此提出了CQ、DQ级低碳铝镇静钢和IF钢优化的光整工艺。

The influence of skin pass process on yield strength , n value and surface quality of hot-dipped galvanized sheet steel were analyzed by experiments . Meanwhile , the optimized skin pass processes for CQ , DQ and IF steel were obtained .

通过建立Al2O3溶解速率和渣成分关系的回归正交设计模型，精确预测铝镇静钢连铸保护渣的夹杂物吸收能力，并通过建立的非线性规划模型对该保护渣进行优化设计。

The inclusion absorption ability of mold powder for Al-killed steels could be predicted accurately by established regression analysis model for relation between Al_2O_3 dissolution rate and mold powder ingredient , and the mold powder for Al-killed steels has been optimized and designed by established nonlinear programming model .

针对国内某厂60t中间包浇注低碳铝镇静钢的多次试验数据，从理论上建立了浇注过程中中间包钢水氧含量的预测模型。

According to experimental data of continuous casting , low carbon Al-killed steel in 60 t tundish , a quantitative prediction model for oxygen content of steel in tundish is established .

低碳铝镇静钢（LCAK）常用于生产冷轧板，要求铸坯有高的洁净度。

High cleanliness is required for low carbon aluminum killed ( LCAK for short ) steel which is widely used for production of cold rolled sheet .

低碳铝镇静钢表面缺陷控制

The surface defects control of low carbon aluminium - killed steel

低碳铝镇静钢铝锰铁脱氧合金化试验

Experiment on Fe-Al-Mn deoxidizing and alloying of low-carbon aluminium killed steel

钢锭模内吹氩提高镇静钢质量的原理

Principle of improving killed steel quality by blowing Ar into molds