焊接性能

TLP焊用非晶态中间层合金的制备及焊接性能

Preparation and welding performance of amorphous interlayer alloys for TLP bonding

GL渗铝钢管合金渗层相组成、变形及焊接性能研究

Phase constitutions in the alloy layer , deformation and welding performance of the calorized steel pipe

U（71）Mn重轨钢焊接性能的模拟研究

Analog Study of Weldability of U_ ( 71 ) Mn Heavy Rail Steel

CO2焊模糊波控逆变电源与平特性逆变电源焊接性能对比研究

Comparison of Welding Characteristic of Fuzzy Wave Contol Electrical Power Source and Constant Voltage Power Source of Co ~ 2 Welding

开关式TIG焊电源的焊接性能分析

Analysis of Welding Performance of IGBT Switch Type TIG Welding Power Source

经XRD和EDS分析烧结后金/铂得到了很好的合金化，且焊接性能良好。

By XRD and EDS analysis , Au / Pt powder obtain good alloying and has good weld ability .

添加WC改善Ni3Al的焊接性能

Improvement of Ni_3Al Welding Property with Addition of WC

灰口铸铁含C、S、P较多，强度低，塑性差，这就决定了其焊接性能较差，焊接接头易发生冷、热裂纹。

Gray iron is of more C , S , P , low-intensity , poor plastic , these characteristics determine that its welding ability is poor , welded joints are easy to produce cold & heat cracks .

Sn-Ag-Cu焊料中金属间化合物对焊接性能的影响

Effect of the IMC in Sn-Ag-Cu Solders on Soldering Properties

结果表明：Fe含量在0.05%～0.20%范围时，Ti&500合金具有良好的焊接性能，焊缝具有很强的腐蚀抗力；

Experimental results showed that , with Fe contents from 0.05 wt % to 0.2 wt % , Ti 500 alloy possessed good welding properties . The welds showed great corrosion resistance .

采用在高体分碳化硅增强铝基复合材料表面化学沉积NiP合金镀层的方法来改善焊接性能。

The solderability of SiC p / Al composite materials is improved by electroless Ni-P alloy plating on its surface .

针对武钢新近开发的高性能管线钢X80钢进行了焊接性能研究。

Weldability test on X80 steel newly produced in WISCO was carried out .

铁路车辆用6005A铝合金大型材焊接性能研究

Study on the Welding Property of 6005A Aluminium Alloy Large - sized Profile for Vehicle Fabrication

简述低碳结构钢微合金系的发展，重点介绍NbV和NbTi微合金钢在强度、韧塑性、织构及焊接性能方面的差异。

The development of low carbon structural microalloyed steels was reviewed . The differences of strength , toughness , plasticity , texture and welding property between the Nb V and Nb Ti microalloyed steels were analyzed .

基于Fe-Ni（36wt.%）合金的应用背景及使用环境，对合金焊接性能研究的重要性也日益凸显出来。

Based on the significant application background of Fe-Ni ( 36wt . % ) alloy , it is very essential to investigate its weldability .

SrTiO3环形压敏电阻器银电极焊接性能研究

Study on soldering performance of silver electrode in SrTiO_3 ring varistor

针对国产600MW亚临界机组锅炉末级过热器采用焊接性能较差的SA213-T91钢材。

SA213-T91 steel with inferior welding performance is used on end superheater of domestic-made600MW subcritical boil-er .

Sn-Ag-Bi系钎料焊接性能研究

The Solder ability of the Solder Based on Sn-Ag-Bi

讨论高含钴量的YG18硬质合金的激光焊接性能。

This paper discussed the laser weld ability of YG18 Cemented Carbide .

通过对紫铜与不锈钢的焊接性能分析和试验，确定了合理的TIG焊焊接工艺，获得了优质的焊接接头，解决了紫铜管与不锈钢管对接焊接的技术难题。

By weldability analysis and test of red copper and stainless steel , the reasonable welding procedure of TIG were ascertained and good welding , joint was gotten . The welding problem of red copper pipe and stainless steel pipe was resolved .

激光重熔在钎料凸点成形中的应用Sn-Ag-Bi系钎料焊接性能研究

Research Status and Application of Laser Reflow on Solder Bump Forming of Area Array Packages The Solder ability of the Solder Based on Sn-Ag-Bi

本文介绍P91管材的基本特征、焊接性能、焊接工艺及焊接质量检验，并阐述如何做好焊接质量控制。

The paper introduces the basic feature , the welding property , the welding process and the welding quality inspection of P91 steel , And It deals with how to make the welding quality control .

Al-Mg-Mn-Sc-Zr合金强度高、塑性好、焊接性能优良，具有较好的抗腐蚀性能，在航天、航空领域有着广泛的应用前景。

Al-Mg-Mn-Sc-Zr alloy is a structure material of high strength and plasticity , good welding property and corrosion resistance used widely in the area of aviation and spaceflight .

Inconel601合金具有良好的焊接性能，但由于其表面张力大，熔池液态金属的流动性能较差，获得的焊缝熔深较浅，在同等的TIG焊工艺参数下熔深不足碳钢的1/2。

However , due to its large surface tension , the fluidity of the welding pool is poor and it is difficult to get a larger weld penetration . The weld penetration of Inconel alloy 601 is less than the half of carbon steel under the same welding parameter .

结果表明，DW-100焊丝在30.0V/260A情况下可以获得比较理想的焊接性能。

It is shown that flux cored wire of DW-100 performing in 30.0 V / 260 A specification has comparatively ideal welding property .

叙述了最近发展起来的极有前途的变形Zn-Cu-Ti合金的成分与力学性能、生产工艺、焊接性能、弯曲性能及其应用。

This article introduces the composition and mechanical properties of deformed Zn-Cu-Ti alloys . Their technology welding process , bending properties and as well as applications are provided .

Al-Zn-Mg系合金具有高的强度、韧性，良好的焊接性能和工艺性能，是建筑、军用设施、航空航天器与地面车辆和装备的主要焊接结构材料。

Al-Zn-Mg alloy series have high strength , ductility , good welding properties and craft performance , and they are mainly used to be welding structural material of building , military facility , aviation spacecraft and ground vehicle .

分析了新型耐热钢（T／P92）焊接性能，并对其焊接工艺、充氩措施及焊后热处理控制要点进行论述。

This paper analyzed the welding capability of the new type heat resistant steel and discussed its welding technology , measures of argon filling and the control points of post weld heat treatment .

至今为止，没有任何一种无铅钎料的性能能够超越Sn-Pb钎料在微电子封装中的地位，无铅钎料的焊接性能和焊点可靠性方面与Sn-Pb钎料还相差很大。

So far , without any kind of the lead-free solder which performance can exceed the position of Sn-Pb solder in the microelectronic packaging . There is still a large difference between the lead-free solders and Sn-Pb solders on the soldering properties and solder joint reliability .

搅拌摩擦焊工艺参数对2519厚板焊接性能的影响

Effect of FSW Parameters on Welding Properties of 2519 Thick Plate