低碳钢

低碳钢连续冷却过程中Ar3温度的预测

Prediction of ar_3 temperature during continuous cooling transformation for low-carbon steel

塑性变形对低碳钢断裂韧性及COD降低系数β的影响

The Effect of Plastic Deformation on Fracture Toughness and COD - Reduced Factor of Low-Carbon Steel

pH值和溶解氧对低碳钢点蚀诱发的影响

Effects of pH Value and Dissolved Oxygen on Pit Initiation Behavior of Mild Steel

pH值对低碳钢在高含盐污水中的腐蚀影响

Effect of pH Value on Corrosion Behavior of Low Carbon Steel in High Salt Waste Water

球化低碳钢中断裂的TEM原位观测

In situ observation of the fracture for a spheroidized low carbon steel

RH真空处理生产超低碳钢时钢水脱碳的数学模型

Mathematical model of decarburization of ultra-low carbon steel during RH treatment

低碳钢中沉淀TiC对氢的捕集

Trapping of hydrogen by precipitate tic in low carbon steel

将表达载体转化E.低碳钢应变诱导铁素体相变发生的温度条件

Induced into E. investigation on the conditions of strain - induced ferrite transformation of low carbon steel

低碳钢CO2激光-脉冲MAG电弧复合焊接工艺研究

CO_2 laser-pulsed MAG hybrid welding of mild steel

低碳钢（F＋A）双相组织高温变形时的动态复原机制

Dynamic restoration mechanism of a low carbon steel during hot deformation in ( f + a ) tow-phase temperature range

CSP热轧低碳钢的强化机制研究

Strengthening Mechanism of Hot-Rolled Low Carbon Steel Produced by CSP

CSP工艺生产的低碳钢中纳米尺寸硫化物

Nanometer Sulfides in Low Carbon Steel Produced by CSP Process

CSP工艺生产低碳钢中的纳米碳化物及其对钢的强化作用

Nano-scale Carbide and Strengthening Effect in Low Carbon Steel Produced by CSP Process

基于元胞自动机方法的CSP流程冷轧低碳钢再结晶过程的模拟研究

Simulation of recrystallization process of cold rolled deep-drawing sheet produced by CSP process based on CA

用表面机械研磨对低碳钢板材进行面处理、经X射线衍射及透射电镜分忻表明，处理后的样品上已形成了纳米结构表层。

A low carbon steel plate was treated by surface mechanical attrition ( SMA ) and its surface layer structure was analyzed by using XRD and TEM .

V和V-N微合金化低碳钢碳氮化物的形变析出

Precipitation Behavior and Effects of Vanadium Carbonitride in V and V-N Microalloyed Mild Steel During Multi-Pass Deformation

刀片采用专门的低碳钢LM槽形，断屑可靠，排屑顺畅。

Dedicated LM geometry for low-carbon steel , reliable chip breaking and smooth chip evacuation .

利用该模型可以分析RH脱碳速度的影响因素，这对优化RH处理生产超低碳钢操作工艺提供指导。

The influence of some factors on decarburization rate has been obtained , which can provide guidance for RH treatment .

在CSP（CompactStripProduction）工艺条件下低碳钢中铁素体的晶内异质形核动力学是一个新的研究领域。

The dynamics of intragranular nucleation of ferrite in the low carbon VN alloyed steel under the compact strip production ( CSP ) is a new research field .

采用电弧喷涂含TiC陶瓷粉末的粉芯丝材，在低碳钢基体上制备了铁基复合涂层。

Iron base composite coatings were deposited on mild steel substrate by arc spraying using cored wire with TiC ceramic powders .

在热模拟单向压缩条件下考察了四个不同C，Mn含量的低碳钢中通过形变强化相变产生的超细铁素体在模拟卷取温度下的长大倾向。

The coarsening tendency of ultra-fine ferrite grains produced by deformation-enhanced transformation was investigated at simulated coiling temperatures by thermal simulating tests in four low carbon steels containing different C and Mn contents .

实验过程中获得了大量与理论分析相一致的低碳钢点蚀声发射源信号，从实验研究上证明了理论分析的正确性。A.时号改正数

In the experiments , a number of acoustic emission signals are achieved , and they are accordant with theoretical analysis results . Time of Emission of Tune Signals

采用等离子束表面冶金技术，在Fe、C合金粉末中添加强碳化物形成元素W、Cr和少量的Al，在低碳钢基体上制备出原位析出的颗粒增强铁基复合涂层。

The in situ particle reinforced Fe-matrix composite coating on a low carbon steel was prepared by plasma jet surface metallurgy using Fe , C , W , Cr , Al alloy powders .

低碳钢Q235是工程中广泛使用的材料，其断裂韧性是工程中进行裂纹监测的重要参数。

Q 235 steel is widely used in engineering .

系统研究了应用离子束混熔技术在低碳钢表面形成的Al和Al合金镀层，大大提高了基体钢的耐腐蚀能力。

The formation of Aluminium and Aluminium alloy coatings on low carbon steel using ion beam mixing has been studied systematically and the coatings increased effectively the capability of corrosion resistance of the steel .

采用CO2作为保护气体消除大熔深激光焊接低碳钢时易发生的气孔问题，并对比研究了CO2和Ar气保护条件下12mm厚低碳钢板激光焊缝的组织和韧性。

CO 2 gas was used as the shielding gas to eliminate porosities in deep penetration laser welding of low carbon steel in this paper .

采用CO2激光器在低碳钢表面进行激光熔覆处理，研究了稀土氧化物在激光熔覆Ni45自熔合金层中的作用。

Ni-based spontaneous melting alloy is selected for laser cladding treatment on the mild steel substrate . Effect of rare earth oxides on Ni-45 spontaneous melting alloy layer by Laser Cladding .

ZrC粒子对低碳钢晶粒细化及力学性能的影响

Effect of ZrC particle on grain refining and properties of low-carbon and low-alloy steel

采用步进式TIG焊，利用计算机控制，对薄板低碳钢平板堆焊的熔透控制进行了研究。

Using the step traveling welding and making use of the computer , the penetration control in TIG welding on mild steel has been studied .

现在越来越多的高强度钢（HighStrengthSteel-HSS）和超高强度钢（UltraHighStrengthSteel-UHSS）被用来代替传统的低碳钢。

Now , more and more high-strength steel ( High Strength Steel-HSS ) and ultra high-strength steel ( Ultra High Strength Steel-UHSS ) were substitued for traditional low carbon steel .