轴承间隙

轴承间隙（1轴颈）

Bearing Clearance ( # 1 Journal )

如果皮带轮受损且存在轴承间隙，请更换空调压缩机。

If pulley is damaged and there is bearing clearance , replace air conditioning compressor .

基于Andrews的轴承间隙动力学模型，推导了不同工况下轴承应力的计算公式，并在摆锤碰撞试验台系统上进行了仿真，并编写了仿真软件。

An equation for calculating the bearing stresses under different operating condition was derived based on the Andrews dynamic model for the bearing clearance . The equation was applied to the simulation of the impact test bench with pendulum and a simulate program was compiled .

带有轴承间隙的裂纹转子分叉与混沌特性

Bifurcation and Chaos of a Cracked Rotor with Bearing Clearances

基于轴承间隙模型的摆锤碰撞试验台仿真研究

Simulation of impact test bench with pendulum based on bearing clearance model

考虑轴承间隙时裂纹转子的故障状态及仿真分析

Fault States and Simulation Analysis of a Cracked Rotor with Bearing Clearances

头脑风暴法提高机组导轴承间隙测调效率的尝试

Attempt to improve efficiency of guide bearing gap by brainstorming

磁悬浮轴承间隙检测专用传感器的研究

Research of Clearance - Sensor in Magnetism Suspend Bearing

考虑轴承间隙的凸轮机构的动力学分析

A Dynamic Analysis of a Cam Mechanism Considering the Effect of Bearing Clearances

计入轴承间隙时轴-滚动轴承系统动力学行为研究

Dynamic Behavior of a shaft-rolling bearing system with clearance

采用刷镀工艺处理柴油机轴承间隙超差问题

Brush-Plating Remedies Oversized Bearings in Diesel Engines

本文主要叙述发电机筒式导轴承间隙对机组安全运行的影响。

This paper mainly describes the influence of generator barrel bearing on the operating safety of the units .

轴承间隙及机油粘度变化对发动机轴承工作性能的影响

The Effect of the Change of Bearing Clearance and Oil Viscosity on the Bearing Working Performance of Engine

如果材料模量与轴承间隙越小，轴承厚度越厚，则压力分布越均匀。

Smaller both the material 's elastic modulus and clearance , and thicker thickness , more even pressure distribution is .

同时还分析了不同的润滑油、转速、载荷和轴承间隙等对轴承性能的影响。

In addition , analyses of the influences of lubricant , speed loading and bearing clearance on bearing performance is also given .

减速机螺旋圆锥齿轮啮合侧间隙及成对圆锥滚子轴承间隙调整

The Adjustment for the Clearance of the Helix Cone Gear Mesh Side for the Reducer and the Clearance of Paired Cone Roller Bearings

首先对噪声信号进行小波包分解，得到含有待诊断柴油机主轴承间隙故障信息的噪声信号时频分布图，并由此定义图像。

We illustrate the wavelet package analysis that can obtain the time-frequency distribution figure of noise signal , which can be used to define gray-image .

结合理论与实验进行了综合分析，探讨了载荷、转速、轴承间隙以及长径比对水润滑复合橡胶轴承摩擦系数的影响及其相互关系；

Discuss the infection and connection to Water Lubricated Composite Rubber Bearing friction quotiety such as : load , rotate speed , bearing 's clearance etc ;

最后，通过模拟仿真并考虑实际工况给出了轴承间隙和节流孔孔径两个关键尺寸。

At last the two key parameters of the bearing clearance and the orifice radius were given by simulation and consideration of the real working conditions .

螺旋槽参数、毕托管上油量和轴承间隙是影响油润滑导轴承润滑可靠性的主要因素。

Spiral groove parameter , oil quantity up through pitot tube and bearing clearance are the main factors that influence lubricating reliability of oil-lubricated guide bearings .

因为工程瓷陶很脆且体胀系数小，所以轴承间隙不得太小，以免发生抱轴变乱。

As the engineering ceramics is very crisp and the expansion coefficient is small , so bearing clearance shall not be too small to hold shaft in order to avoid an accident .

采用多个传感器同时采集位移电压和多个神经网络模型进行迭代求解的方法，实现了对滑动轴承间隙的检测。

Multiple data-gathering sensors were used to gather displacement and voltage , multiple neural network models were used to get a result by iterative way , so that sliding bearing clearance can be measured .

本文的研究充分表明：尽管齿轮机构的输入扭矩保持不变，然而，由于滑动摩擦及轴承间隙的存在，齿轮必产生振动。

It has fully been proved by researches of this article that even though the input torque of the gearing is kept unchanged , the gears surely generate vibration because of the existence of sliding frictions and bearing clearances .

这些问题包括尺寸规范、瓦块接触应力、润滑方式、喷油嘴设计、轴承间隙及轴承承载能力等。

The problems include the size norm , the connect stress of the bearing tile , the lubricating form , the design of the nozzle , the bearing clearance , and the carrying capacity of the bearings and so on .

阐述了减速机圆锥齿轮啮合间隙和成对圆锥滚子轴承间隙的调整方法生产厚螺旋叶片的锥辊轧机的研究

This paper has described the adjusting methods for the clearance of the helix cone gear mesh side of the reducer as well as the clearance of the paired cone roller bearings . Research of Cone Roller Machine of Producing Thick Screw Vane

用有限元法对某型三牙轮钻头的2号牙轮－牙爪进行了静力计算，求得不同轴承间隙时牙爪轴颈及止推面上的接触应力分布规律。

A static analysis of the No. 2 leg-cone of a tricone bit is conducted by the finite element method , and the distribution pattern of the contact stress on the leg journal and thrust surface with different bearing clearances is worked out .

用数值分析方法，研究了齿轮传动比、压力角、螺旋角、齿轮位置、功率、轴承间隙比与宽径比对系统不平衡响应的影响。

By employing the numeric analysis method , the influence of speed ratio , pressure angle , helical angle , gears positions , power , clearance ratio , and width to diameter ratio of bearing , on the response of the system is investigated .

为了验证本文模型的有效性，把仿真结果与没有考虑轴承间隙时的仿真数据以及试验数据进行了对比，表明基于轴承间隙的仿真模型更接近于试验结果。

The simulated results were compared with those of the simulation without consideration of the bearing clearance and those of the experiments , showing the simulation result based on the bearing clearance model was closer to the experimental one than that without considering the clearance .

本文导出了计入这种附加径向压力、齿间摩擦及轴承间隙综合影响的船用齿轮齿面接触疲劳强度优化计算公式。

This paper derives the amendatory formulas for determination of the contact fatigue strength of the marine gearing which involves the synthetical effects of the additional radial pressures , the friction between teeth and the clearances between the gear shaft journal and its bearing during operating .

外场驱动血泵转子轴承配合间隙应选为0.002mm。

The match clearance of blood pump driven by extra magnetic field should be 0.002 mm .