牵引杆

ALLIANCE车钩钩锁铁与牵引杆的几何反求研究铁路货车钩缓装置钩尾扁销螺栓断裂原因分析

Reverse Engineering Based Geometry Model for Alliance Coupler Lock and Drawbar ; Breaking Reason Analysis of Coupler Yoke Bolts on Coupler Draft Gears for Railway Freight Cars

正确认识牵引杆的选择

Correct Knowledge for Selection of Drawbar Choice

SS7型电力机车牵引杆座可靠性分析与改进设计

Reliability Analysis and Improvement Design of Traction Link Seat for SS7 Electric Locomotive

介绍了SS7型电力机车牵引杆座的裂纹情况，应用有限元法分析了裂纹发生的原因，指出在牵引杆座前后加设加强筋板使结构的局部区域刚度失调是造成裂纹的主要原因。

Cracks in the traction link base of SS7 electric locomotive are shown and reasons are analyzed with finite element method . The main reason is pointed out that reinforced sheets are used before and after the traction link base , leading to uneven partial rigidity .

机车牵引杆座细部结构设计及计算分析

Detailed structure design , calculation and analysis of locomotive traction link seat

行标《牵引杆挂车转盘》简介

Brief Introduction for Traffic Standardization of Draw-bar Trailer Turntable

对牵引杆控制单元重新编程。

Re-program the towbar control unit .

牵引杆高度可调式挂车

Trailer with adjustable drawbar height

牵引杆拉力-重量比

Drawbar pull - weight ratio

对无间隙牵引杆的曲线通过性能与传统车钩缓冲装置作了对比；

The curve negotiation performance of slackless drawbar is compared with that of the traditional coupler buffer device ;

采用模型参数化分析方法，讨论了牵引杆长度、主车与拖车和拖车与拖车的铰接点位置对主车与拖车轨迹同辙性的影响。

The effects of drawbar length , articulation joint position on path following performance are investigated using parameter analysis method .

低牵引杆由电子重量分配仪辅助，而防旋防滑装置则保证充分利用车轮的附着力。

Low level traction roads are complemented by electrical weight transfer compensation , while antispin and slip devices ensure that good use is made of adhesion .

脱扣装置包括牵引杆、热元件、双金属元件、磁系统、锁扣及跳扣。

A tripping device comprises a traction rod , a thermoelement , a bimetallic element , a magnetic system , a lock catch , and a jump pin .

履带式拖拉机作业性能的计算机模型对无间隙牵引杆的曲线通过性能与传统车钩缓冲装置作了对比；

COMPUTER SIMULATION OF DRAWBAR PERFORMANCE FOR A TRACKED TRACTOR IN THE FIELD The curve negotiation performance of slackless drawbar is compared with that of the traditional coupler buffer device ;

该技术方案具有如下特点：前后关节车体铰接、走行部2轴与3轴转向架混用、利用牵引杆联结构成四车组单元。

The technical project has the following features : the fore and rear flatcar articulated , the running gear with 2-axle and 3-axle bogie mixture , 4-vehicle unit constructed by traction rod .

采用单牵引杆，其名义牵引高与等效牵引高不相同，但只要名义牵引高达到最佳牵引高，机车的粘着利用率就接近最佳值。

As long as the nominal traction height is same as the optimum traction height , approximate optimum rate of adhesion usage can be reached for the locomotive with single traction rod .

研究表明采用该转向架的车辆水平定位刚度和旁承摩擦系数以及牵引杆纵向刚度对下摇枕结构车辆横向稳定性具有显著影响，三者中任一参数的变化会影响到整车横向稳定性。

The stiffness of primary suspension and the friction coefficient of side bearing and the longitudinal stiffness of the traction rod have a significant impact to the stability of the vehicle , the change of anyone will effect the lateral stability .

你知道牵引楔形杆是什么吗？

Do you even know what a pitching wedge is ?

铁路货车无间隙牵引装置&牵引杆生产工艺

Research and Development on the Manufacturing Technology of Drawing bar of Seamless Traction Device

介绍了带牵引钢带与不带牵引钢带引锭杆跟踪系统的构成及其对工艺过程的控制。

To introduce the constitution and process control of a dummy bar follow-up system with drag belt and without drag belt .