止口

介绍客车车身制造过程中的检验样板，尤其是后围横向弧度、风窗玻璃和风窗止口的检验样板的设计和制作方法

The article introduces the checking templates in manufacturing the bus body , especially in the design and manufacture of the checking templates that are used in back wall transverse radian , windscreen and windshield rabbet

内筒的一端端口法兰内径处设有止口，用于与相邻筒节的对应端无止口法兰插接。

The inner diameter part of the flange at one port of one end of the inner cylinder is provided with a rabbet for splicing with a flange without a rabbet at a corresponding end of an adjacent elbow .

确定为E.活塞止口工艺公差的确定

And E. Determining the Machining Tolerance of Locating Flange of Piston Open End

狭长盲视空间中精密止口的柔顺对接装配

Flexible Butt-Joint Assembly for Precise Flange in Long and Narrow Space

精密止口自动对接装配装置设计

Design of the Automatic Device for Butt Assembling of the Exact Flanger

柴油机缸体气缸孔止口粗加工组合机床

A Combined Machine for Rough Boring of Cylinder and Scraping of Spigots

矿用隔爆型磁力起动器止口变形的消除方法

Methods of eliminating the mouth deformation of the mine flame-proof magnetic starter

190型柴油机机体上止口裂纹的检查和修复

Detection and Repairing of Cylinder Block in the 190 Series Diesel Engine

可调节止口高度；具有防水密封功能；

The seam height can be adjusted , water-tight .

精密止口自动装配的设计与实现

Design and Realization of Automatic Assembly of Precise Flangers

止口弯曲成形模设计

Design of the Bending Die for Retaining Rings

粗车电机机座止口的胀紧夹具

Expansion Jig for Rough Turning of Frame Spigot

小止口拉森钢板桩阻水围堰施工工艺

Water Blocking Cofferdam Construction Technology by Using Larssen Sheet Piles with Small Seam Allowance

精车活塞止口专机自动上下料系统的研制

Development of an automatic loading and unloading piston system of finish machining piston end mouth

发电机轴内止口测量仪

Internal Spigot Measuring Instrument for Generator Shaft

该设备系加工拖辊钢管两端止口的专用设备。

The equipment is special equipment for processing the rabbet of two ends of roller steel tube .

精密止口在进行自动装配作业时容易出现楔紧和卡阻现象，一直是此类装配作业的难点。

During the process of automatic assembly of precise flangers , the workpieces are usually wedged and locked .

通过对止口成型过程分析，提出更合理的工艺方案，以满足生产需要。

Analysing the structure shaping process , more reasonable technological proposals are raised to be suited to manufacture .

以曲轴箱精铣主轴承止口位调刀装置的设计为例，介绍一种简易的刀具微调装置。并对该设计方法进行综合论述。

An easy fine adjustment device for cutter is introduced , giving detailed discussion to the design method .

发现内外骴骨因止口左右不对称导致严重扭脾。

Found inseam and outseam is serious torquing causing serious unbalance outseam inseam fold on ( left right ) .

精铣缸体顶面、精镗缸孔及止口数控自动线的研制

Finish Milling Head Face of Cylinder 、 Finish Boring Cylinder Hole and the Design of Digital Control Automatic Line

介绍一种简单、实用的风窗止口的设计方法。

SECRET WINDOW In this article , a simple and practical design method for the windshield fixing frames is introduced .

描出里面的翻领线，去掉门襟止口处尖驳头处的缝份。

Trace inside the roll line and remove the seam allowance from the front edge and peak of the lapel .

前、后端盖利用螺钉及止口固定，同时将转子总成固定。

The front end cover and the rear end cover are fixed by screws and rabbets . Meanwhile , the rotor assembly is fixed .

仔细地把粘合衬放在上面，与门襟止口对齐。用一块湿布覆盖并定位粘合。

Carefully place the fusible piece on top , matching it to the jacket edges . Cover with a damp cloth and fuse in place .

本文根据活塞具体工艺过程的要求，提出了确定止口工艺公差的原则和计算方法。

Basing on the requirements in machining of the piston , principle and calculation method for determining the machining tolerance of locating flange of piston open end are proposed .

该多路温度检测系统已成功应用于大尺寸轴类零件（水轮机、汽轮机止口）加工时热变形误差补偿的试验中。

The multiplex temperature measuring system had applied to the experiment of compensating thermal error of large-scale shaft parts ( water turbine , steam turbine parts ) in machining process triumphantly .

改进设计的M&827止口直径测量尺能够直接测量出被加工零件的实际加工尺寸偏差，提高零件加工质量。

After modified design , the M-827 measuring rule used to measure step diameter can measure the actual dimension deviation of machined parts directly and quality of the parts is improved too .

在服装工艺实践课上，由于学生的实践操作技术水平有限，往往上衣止口在缝制过程中容易出现各种各样的问题。

During the course of the garment technology , the up-garments front edge can bring various flaws in the event of the unsuitable sewing , due to the students finite practice technology operation .

根据车轮报废线、止口的工艺要求，设计了专用加工刀具，并对不同刀具设计方案进行了比较。

Based on the technological requirements of the condemning line and limiting slot of railway wheels , the special cutting tools are designed , and two kinds of tool design schemes are compared .