杆头

ɡǎn tóu
  • club head
杆头杆头
  1. 使用运动跟踪创建一个后面的球手的杆头议案挥杆路径。

    Use Motion Tracking to create a motion swing path behind a golfer 's club head .

  2. 利用挤压成型的方法,制备了应用于钛合金高尔夫球杆头精密铸件的陶瓷型芯。

    The ceramics core was prepared by extrusion moulding applied in the titanium alloy golf club head .

  3. 必须让杆头一气呵成地挥出。

    You must allow the clubhead to swing freely .

  4. 整个挥杆过程中要使杆头始终保持在同一高度。

    Keep the head of the club the same height throughout the swing .

  5. 订货的场合,如果对活塞杆头、油缸盖的U形环的宽度、销子的直径等尺寸方面另有要求时,建议采用能够利用的本公司现有的模锻件。

    If any other requirements for piston rod head , U type ring width of cylinder lid , and diameter of pin are needed when placing an order , it is recommended to use our existing forged pieces .

  6. 杆头加工偏差对抽油杆强度的影响

    Influence of machining deviation of sucker rod head on rod strength

  7. 其杆头比现代的杆头要长和细。

    The heads were longer and slender than modern club heads .

  8. 消失模法试制杆头类铸件

    Rod Castings With One Large Section End Made by Lost Foam Casting

  9. 推杆杆头冷挤压新工艺

    Cold extrusion process for the engine racing bar head

  10. 取出断入钻头内的钎杆头技术研究

    Study on Technique of Drawing out Head of Boring Bar Broken inside Bit

  11. 用金属的头代替了传统的木制杆头的高尔夫球棍。

    A golf club with a metal head instead of the traditional wooden head .

  12. 你是什么,银枪腊杆头?

    What are you , a faggot ?

  13. 一种具有锁具的按压式排档杆头。

    The utility model relates to a press type gear shift rod head with a lockset .

  14. 排档杆头上设有容置套管的容置槽;

    A containing groove for containing the casing pipe is arranged on the gear shift rod head .

  15. 通过对剑杆头表面的失效磨损分析,结合失效机理分析剑杆头的失效原因。

    By analyzing the failure of the surface of the rapier head wear . combined with the failure mechanism , find our the failure cause .

  16. 轻量化研磨铝合金材质能使重量分散至杆头周边,精密研磨后的外观予人洁净与极佳的质感。

    Lightweight milled aluminum body allows for distribution of weight to the perimeter of the head . Precision milling gives it a clean , rich look .

  17. 采用杆头跟踪预热处理技术,消除了杆头调质缺陷,提高了抽油杆应用的可靠性。

    The thermal refining defect of rod head was eliminated by the tracking preheat treatment of rod head to improve the reliability of the pumping rod application .

  18. 结果表明,氧化锆陶瓷型芯的物理性能能够满足钛合金高尔夫球杆头铸造要求,该陶瓷型芯与钛合金液不发生明显的界面反应。

    It is shown that the ceramics core is excellent in the physical characteristics . And it is not obvious in the interface reaction with liquid of titanium .

  19. 不管是出于生气或其他原因,球员都应当避免对球场造成损伤,如试挥时造成草皮翻起,用杆头击打地面,等等。

    Players should avoid causing damage to the course by removing divots when taking practice swings or by hitting the head of a club into the ground , whether in anger or for any other reason .

  20. 中空内外套丝螺杆一端为有坡度中空螺纹杆头,另一端为六边型中空螺杆,中部为空心内外套丝螺杆;

    The hollow internal and external threading screw has a hollow screw head with slope on one end , a hexagonal hollow screw on the other end , a hollow internal and external threading screw in the middle .

  21. 在分析了内燃机推杆杆头以切削为主的传统加工工艺存在问题的基础上,根据该零件的技术要求,依据冷挤压理论,制订了该零件的冷挤压件图。

    On the basis of analyzing the problems existed in traditional machining processes for the push rod end of internal combustion engine , the cold extrusion part drawings are made according to the part specifications and the cold extrusion theory .

  22. 抽油杆杆头自动荧光磁粉探伤机的研制与应用

    Research and application of sucker rod head automatic flaw detection machine of fluorescence magnetic particle

  23. 具体内容如下:(1)对推力杆球头铸造工艺进行分析讨论。

    The specific steps are as follows : ( 1 ) Analyzed and discussed the casting process of thrust rod ball .

  24. E/P杆加热锻头机床床体结构的强度、刚度设计与有限元计算

    Stiffness , Strength and FEM Calculation of Machine Tool Structure of E / P Shaft

  25. 空心抽油杆摩擦焊接头的焊后热处理工艺研究

    Investigation into Heat-treatment Processing for Friction Welded Joint of Hollow Sucker Rods

  26. 空心抽油杆摩擦焊接头断裂失效分析

    Failure analysis of friction welded joint of hollow sucker rod

  27. 空心抽油杆摩擦焊接头强韧性控制

    Controlls of Strength and Toughness of Friction Welded Joints of Hollow Sucker Rods

  28. 杆式滴头的研究与试验应用

    Research and Experimental Application of Pole Dripper

  29. 该滚珠丝杆的端头连接着驱动电机。

    The end head of this ball silk pole is connecting the electrical machinery of urging .

  30. 未装配的工具用金属陶瓷板、杆、刀头及类似品。

    Plates , sticks , tips and the like for tools , unmounted , of cermets .